Hayter Sprint 41 616E User Manual (English)

Questions and Answers:

C
courtney70Aug 14, 2025
Why won't my Hayter Sprint 41 616E engine start?
- G
  Gabriel HensleyAug 14, 2025
  There are several reasons why your Hayter Lawn Mower engine might not start. It could be due to the engine being under load, so try raising the height of cut. Alternatively, the fuel might be incorrect or contaminated, in which case you should drain the tank and fill it with the correct fuel. Other potential causes include a disconnected spark plug lead (connect it), the engine brake not being released (operate the engine brake lever), a faulty spark plug (clean and adjust the gap or replace it), a discharged battery (charge the battery), or a wiring fault (check the wiring).
V
Vanessa WalkerAug 18, 2025
What to do if the engine will not turn over on my Hayter Sprint 41 616E?
- T
  thomas12Aug 18, 2025
  If the engine will not turn over on your Hayter Lawn Mower, ensure that you operate the engine stop lever. Also, check the oil level. There might be an obstruction under the deck, so remove it. If your mower has a battery, it might be discharged, so charge the battery.
L
lsmithAug 21, 2025
What to do if the discharge chute blocks on my Hayter Sprint 41 616E Lawn Mower?
- D
  Dustin SwansonAug 21, 2025
  If the discharge chute on your Hayter Lawn Mower is blocked, it could be due to several reasons. The grass might be wet, in which case you should mow dry grass. The cut height might be too low, so increase it. The grassbag might be full, so empty it. Finally, airflow through the grassbag might be restricted, so clean the grassbag.
J
Jenna HicksAug 25, 2025
What to do if my Hayter Lawn Mower has poor grass collection?
- J
  James BlankenshipAug 25, 2025
  If your Hayter Lawn Mower has poor grass collection, it could be due to restricted airflow through the grassbag, so clean the grassbag. Alternatively, the discharge chute might be blocked, so remove the blockage. Wet grass can also cause this issue, so mow in dryer conditions. Finally, make sure the grassbag isn't full and empty it if it is.
J
Jenna McgeeAug 28, 2025
What to do if my Hayter Sprint 41 616E engine runs rough?
- K
  Karen Foster MDAug 28, 2025
  If your Hayter Lawn Mower engine is running rough, it could be due to a few reasons. The spark plug lead might be becoming disconnected during use, so connect it. The spark plug might be faulty, so clean and adjust the gap or replace it. The air cleaner could be blocked, so service it. Finally, the fuel might be incorrect or contaminated, so drain the tank and fill it with the correct fuel.
S
Stephen GarciaAug 31, 2025
Why is my Hayter Sprint 41 616E Lawn Mower engine hard to push?
- W
  William BrownAug 31, 2025
  If your Hayter Lawn Mower is hard to push, it could be because the cut height is too low; try increasing it. Alternatively, the wheels or roller might be damaged, in which case you should inspect and replace them as necessary.
P
Pamela FarleySep 4, 2025
What to do if my Hayter Lawn Mower engine vibrates excessively?
- S
  Steven MorrisonSep 4, 2025
  If your Hayter Lawn Mower engine vibrates excessively, it could be due to a loose mounting bolt, so tighten the bolts. It could also be a loose cutterblade bolt, so tighten the bolt. Another possibility is that the cutterblade is out of balance, so balance the cutterblade. If none of these work, the crankshaft might be bent, in which case you should consult your dealer.
J
Jennifer ThompsonSep 7, 2025
What to do if my Hayter Sprint 41 616E engine runs then stops?
- W
  wattsamySep 7, 2025
  If your Hayter Lawn Mower engine runs and then stops, it could be due to fuel starvation, so fill the fuel tank. Alternatively, the fuel cap vent might be blocked, so clean the fuel cap vent.
R
rnelsonSep 10, 2025
How to fix an uneven cut with my Hayter Sprint 41 616E?
- K
  Kristin StephensSep 10, 2025
  If your Hayter Lawn Mower is leaving an uneven cut, it could be due to undulating ground conditions, so change the direction of travel. The cutterblade might be worn, so sharpen it. It's also possible that the cutterblade is out of balance, so balance it. Finally, check if the wheels or roller are damaged and replace them as necessary.