Hayter Motif 41 Push User Manual (English)

Questions and Answers:

W
wmaddenAug 17, 2025
Why my Hayter Lawn Mower engine will not start?
- P
  pwilliamsonAug 17, 2025
  If your Hayter Lawn Mower engine won't start, several factors could be at play. It might be under load, in which case you should raise the height of cut. The fuel could be incorrect or contaminated, requiring you to drain the tank and fill it with the correct fuel. Check if the spark plug lead is disconnected and connect it. Ensure the engine brake is released by operating the engine brake lever. Inspect the spark plug for faults, cleaning, adjusting the gap, or replacing it if necessary. Finally, examine the wiring for any faults and correct them.
A
Angela WrightAug 20, 2025
How to fix a Hayter Motif 41 Push engine that runs rough?
- J
  Jamie MasseyAug 20, 2025
  If your Hayter Lawn Mower engine is running roughly, there are a few things you can check. The spark plug lead may be becoming disconnected during use, so ensure it's securely connected. The spark plug itself might be faulty, requiring cleaning, gap adjustment, or replacement. A blocked air cleaner could also be the culprit, so service it. Finally, incorrect or contaminated fuel can cause rough running, so drain the tank and fill it with the correct fuel.
E
Elizabeth PattersonAug 22, 2025
Why does my Hayter Motif 41 Push Lawn Mower engine vibrate excessively?
- S
  Sherri DodsonAug 22, 2025
  Excessive vibration in your Hayter Lawn Mower engine can stem from several issues. Check for loose mounting bolts and tighten them. Similarly, inspect the cutterblade bolt and tighten if necessary. An out-of-balance cutterblade can also cause vibration, so balance it. If these steps don't resolve the issue, a bent crankshaft might be the cause, and you should consult your dealer.
T
Taylor PittmanAug 26, 2025
What to do if Hayter Motif 41 Push engine runs then stops?
- J
  Joseph WrightAug 26, 2025
  If your Hayter Lawn Mower engine runs and then stops, the issue might be fuel-related. Fuel starvation could be the cause, so fill the fuel tank or turn the fuel shutoff valve to the ‘ON’ position. Another potential problem is a blocked fuel cap vent, which you should clean.
A
Ann GonzalezAug 28, 2025
Why does the discharge chute block on my Hayter Lawn Mower?
- J
  Jason SuttonAug 28, 2025
  If the discharge chute of your Hayter Lawn Mower keeps blocking, consider these factors: if the grass is wet, mow dry grass instead. If the cut height is too low, increase it. If the grassbag is full, empty it. If there is no airflow through the grassbag, clean the grassbag.
M
Monica MedinaAug 30, 2025
How to fix uneven cut with Hayter Motif 41 Push?
- R
  Rebecca JonesAug 30, 2025
  An uneven cut with your Hayter Lawn Mower can result from a few things. Undulating ground conditions might be the cause, so try changing your direction of travel. A worn cutterblade can also lead to an uneven cut, so sharpen it. Additionally, check if the cutterblade is out of balance and balance it. Damaged wheels or rollers could also be the problem; inspect them and replace as necessary.
C
Cindy WestSep 2, 2025
Why is my Hayter Motif 41 Push engine smoking?
- S
  Susan WadeSep 2, 2025
  If your Hayter Lawn Mower engine is smoking, it could be due to excess oil, so check the oil level. Alternatively, the air cleaner cartridge might be oil-soaked or blocked, requiring you to service the air cleaner.
K
kboydSep 5, 2025
Why is my Hayter Motif 41 Push leaving poor grass condition?
- J
  James NorrisSep 5, 2025
  Poor grass condition after mowing with your Hayter Lawn Mower can be attributed to several factors. A lack of airflow through the grassbag might be the cause, so clean the grassbag. A blocked discharge chute could also be the culprit, so remove the blockage. Mowing wet grass can also lead to poor grass condition, so mow dry grass. Finally, check if the grassbag is full and empty it if necessary.
L
Lori WeissSep 7, 2025
Why is my Hayter Motif 41 Push hard to push?
- M
  Mrs. Colleen Gutierrez DVMSep 7, 2025
  If your Hayter Lawn Mower is hard to push, the cut height might be too low, so increase it. Also, the wheels or roller might be damaged, so inspect them and replace them as necessary.