Hayward T-CELL-3 - User Manual

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
092641 RevA
Hayward Canada
400 Connell Drive, Suite 6100
Berkeley Heights, NJ 07922
Phone: (908) 355-7995
www.hayward-pool.ca
T-CELL-3
GLX-CELL-3-W
NEW MENU SETTING REQUIRED!
You must configure your controller for use with the T-CELL-3 or GLX-CELL-3-W chlorinator cell before attempting to operate. Incorrect
configuration will cause inaccurate salt readings, improper operation, and possible system shutdown.
The T-CELL-3 and GLX-CELL-3-W are designed for pools up to 15,000 gallons. They are compatible with the following models only and will
NOT work with earlier versions:
• AQR (AquaRite - all 2009 or later) - firmware version 1.5 or later
• AQR-PRO (AquaRite Pro) - operating with firmware 1.10 or later
• PL-P-4 (ProLogic P4) - operating with firmware 4.10 or later
• PL-PS-x (ProLogic PS) - operating with firmware 4.10 or later
Connecting to an AQR or AQR900:
1. Slide the Main Switch to the “Auto” position.
2. Push the Diagnostic button repeatedly until “t-xx” appears on the display (“t-15” is the factory default).
3. To change cell type, slide the Main Switch from “Auto” to “Super Chlorinate” and back to “Auto”. Repeat this process until the “t-9” is
displayed.
4. Push the Diagnostic button to exit.
Connecting to an AQR-PRO:
1. Verify that the firmware version is 1.10 or greater by pushing the “Info” button, then”>” repeatedly until the firmware revision is shown.
If the firmware version is less that 1.10, the T-CELL-3 or GLX-CELL-3-W cannot be used.
2. Access the Settings Menu by pushing the “Settings” button.
3. Push “>” until Chlor. Config is displayed, then push “+”.
4. Push “>” repeatedly until “Cell Type” is displayed.
5. Push “+” or “-” until “T-CELL-9” is displayed.
6. Exit Settings Menu by pushing the “Info” button.
Connecting to a PL-P-4 or PL-PS-x:
1. Verify that the firmware version is greater than 4.10 by entering the Diagnostic Menu and repeatedly pushing the “>” until the Main
Firmware revision is shown. If the firmware version is less that 4.10, the T-CELL-3 or GLX-CELL-3-W cannot be used.
2. Enter the Configuration Menu.
3. Push “>” until Chlor. Config is displayed, then push “+”.
4. With the Chlorinator Enabled, push “>” repeatedly until “Cell Type” is displayed.
5. Push “+” or “-” until “T-CELL-3” is displayed.
6. Exit Settings Menu by pushing the “Menu” button.

Summary

New Menu Setting Required

AQR;AQR900 Configuration Steps

Instructions for configuring the T-CELL-3 or GLX-CELL-3-W with AQR or AQR900 controllers.

AQR-PRO Configuration Steps

Steps to connect and configure the T-CELL-3 or GLX-CELL-3-W with AQR-PRO controllers.

PL-P-4;PL-PS-x Configuration Steps

Procedure for connecting and configuring the T-CELL-3 or GLX-CELL-3-W with PL-P-4 or PL-PS-x.

Important Operational Information

Chlorination Setting Adjustment

Guidance on adjusting chlorination settings based on filter pump run times and pool filtration cycles.

Installation Configurations

Diagrams and explanations for vertical and inverted installation of the salt cell for optimal flow.

Hayward T-CELL-3 Specifications

General

Model	T-CELL-3
Cell Size	Small
Pool Size	Up to 15, 000 gallons
Salt Requirement	Yes
Flow Rate	20 GPM minimum
Type	Salt Cell
Compatibility	Hayward systems
Salt Concentration	2700-3400 ppm
Voltage	12 V
Warranty	1 year