Hayward TCELL940 - User Manual

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
092625 RevC
Hayward Industries
400 Connell Drive, Suite 6100
Berkeley Heights, NJ 07922
Phone: (908) 355-7995
www.hayward.com
TCELL940
TCELL940-W
MENU SETTING MAY BE REQUIRED!
The TCELL940 and TCELL940-W are cells designed for pools up to 40,000 gallons. When replacing an existing T-CELL-15, GLX-CELL-15,
or TCELL940, no re-configuration is necessary.
If configuration is required, refer to the information below. Incorrect configuration will cause inaccurate salt readings, improper operation,
and possible system shutdown.
CONFIGURATION is necessary with the following models:
• AQR (Aqua Rite - all 2009 or later) - firmware version 1.5 or later
• AQR-PRO (Aqua Rite Pro)
• OmniLogic & OmniPL - refer to owner’s manual for configuration
• PL-P-4 (Pro Logic P4)
• PL-PS-x (Pro Logic PS)
• AQ-LOGIC-P-4 (Pro Logic P4)
• AQ-LOGIC-PS-x (Pro Logic PS)
• AQR900 series - all
NO CONFIGURATION is necessary with the following models:
• AQ-RITE (Aqua Rite - 2008 and earlier) - firmware earlier than version 1.5
• AQ-RITE-XL (Aqua Rite XL)
Connecting to an AQR or AQR900:
1. Slide the Main Switch to the “Auto” position.
2. Push the Diagnostic button repeatedly until “t-xx” appears on the display (“t-15” is the factory default). If “t-15” is displayed, skip to
step 4.
3. To change cell type, slide the Main Switch from “Auto” to “Super Chlorinate” and back to “Auto”. Repeat this process until the “t-15” is
displayed.
4. Push the Diagnostic button to exit.
Connecting to an AQR-PRO:
1. Access the Settings Menu by pushing the “Settings” button.
2. Push “>” until Chlor. Config is displayed, then push “+”.
3. Push “>” repeatedly until “Cell Type” is displayed.
4. Push “+” or “-” until “T-CELL-15” is displayed.
5. Exit Settings Menu by pushing the “Info” button.
Connecting to an AQ-LOGIC-P-4, AQ-LOGIC-PS-x, PL-P-4 or PL-PS-x:
1. Enter the Configuration Menu.
2. Push “>” until Chlor. Config is displayed, then push “+”.
3. With the Chlorinator Enabled, push “>” repeatedly until “Cell Type” is displayed.
4. Push “+” or “-” until “T-CELL-15” is displayed.
5. Exit Settings Menu by pushing the “Menu” button.

Summary

TCELL940 Configuration and Connection Guide

Compatibility and Configuration Requirements

Identifies Hayward controllers requiring and not requiring TCELL940 configuration.

Connecting to AQR and AQR900 Controllers

Step-by-step guide for connecting TCELL940/TCELL940-W to AQR/AQR900 controllers.

Connecting to AQR-PRO Controllers

Step-by-step guide for connecting TCELL940/TCELL940-W to AQR-PRO controllers.

Connecting to AQ-LOGIC and Pro Logic Controllers

Step-by-step guide for connecting TCELL940/TCELL940-W to AQ-LOGIC/PL controllers.

Important Operational and Installation Information

Filtration Cycles and Chlorination Settings

How to adjust chlorination based on filter pump run time and pool conditions.

Low Flow Rate and Pump Speed Considerations

Importance of adequate flow for salt cells, especially with variable speed pumps.

Recommended Installation Configurations

Vertical or inverted installation for optimal cell performance with variable speed pumps.

Hayward TCELL940 Specifications

General

Model	TCELL940
Pool Size Compatibility	Up to 40, 000 gallons
Cell Type	Turbo Cell
Salt Level	2700-3400 ppm
Compatible Systems	Aqua Rite, Aqua Rite Pro, Aqua Plus, Pro Logic
Flow Rate	Minimum 20 GPM
Voltage	220V
Water Temperature	50°F
Warranty	3 Year Limited