Heat-N-Glo ST-TRC User Manual

1
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Models:
Pier-TRC
ST-TRC
L-Corner-TRC
R-Corner-TRC
Installers Guide
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
Underwriters
Laboratories Listed
501-900 REV. O 2/03
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
Please contact your Heat-N-Glo dealer with any
questions or concerns. For the number of your nearest
Heat-N-Glo dealer, please call 1-888-427-3973.
Printed in U.S.A. Copyright 2003
Heat-N-Glo, a division of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

Heat-N-Glo ST-TRC Specifications

General

Vent Type	Direct Vent
Fuel Type	Natural Gas or Liquid Propane
Glass Type	Ceramic
Control Type	Remote Control
Log Set Material	Ceramic Fiber
Burner Material	Steel
Warranty	Limited Lifetime

Summary

Safety and Warning Information

Approvals and Codes

Appliance Certification

Details the testing and listing of fireplace models by laboratories.

Installation Codes

Outlines requirements for local building codes and national standards for installation.

High Altitude Installations

Provides guidance on adjusting appliance performance for installations at higher elevations.

Getting Started

Introducing the Heat-N-Glo Gas Fireplaces

Explains the design and operation of direct vent gas fireplaces.

Pre-installation Preparation

Covers important checks and preparations before installing the fireplace.

Installing the Fireplace

Locating the Fireplace

Shows space and clearance requirements for fireplace placement within a room.

Clearance Requirements

Specifies minimum clearances from the fireplace to combustible materials.

Framing the Fireplace

Provides framing dimensions and methods for installing the fireplace.

Installing the Vent System

Vent System Approvals

Lists approved D-series direct vent pipe components and terminations.

Identifying Vent Components

Explains the different vent system parts and their configurations.

Installing Vent Components

Details the process of attaching vent components to the fireplace and connecting them.

Venting Out the Rear Vent

Instructions for connecting the vent system to the rear starting collars.

Venting Out the Top Vent

Instructions for connecting the vent system to the top starting collars.

Vent Termination

Describes how to attach and secure the vent termination cap to the building.

For Horizontal Terminations

Specific steps for attaching horizontal vent terminations.

For Vertical Terminations

Steps for locating, installing, and sealing vertical vent terminations through the roof.

Positioning, Leveling, and Securing the Fireplace

The Gas Control System

Standing Pilot Ignition System

Describes the components and operation of the standing pilot system.

Intermittent Pilot Ignition (IPI) System

Details the components and operation of the intermittent pilot ignition system.

The Gas Supply Line

Gas Pressure Requirements

Wiring the Fireplace

For Standing Pilot Ignition Wiring

Explains wiring requirements for the standing pilot ignition system.

Optional Accessories

Details wiring for optional accessories like fans and remote controls.

Wall Switch

Instructions for installing and wiring a wall switch for fireplace operation.

For Intermittent Pilot Ignition (IPI) Wiring

Explains wiring requirements for the intermittent pilot ignition system.

Operation using Battery Power

Information on using the optional battery backup system.

Finishing

Hearth Extensions

Discusses the aesthetic desirability and requirements for hearth extensions.

Installing Trim, Logs & Ember Material

Installing the Trim

Guidelines for installing trim and covering gaps around the fireplace.

Positioning the Logs

Instructions for positioning gas logs for optimal flame appearance.

Placing the Ember Material

Steps for applying ember material for a realistic flame effect.

Shutter Settings

Table indicating shutter settings for different models and gas types.

Before Lighting the Fireplace

Lighting the Fireplace

After the Installation

Final steps after installation, including leaving the manual.

Maintaining and Servicing Your Fireplace

Fireplace Maintenance

Overview of regular servicing and annual check-ups for the fireplace.

Replacing old ember material

Procedure for replacing ember material during annual maintenance.

Cleaning Burner and Controls

How to clean the burner and control compartment.

Cleaning Flame Sensor Rod (IPI Systems)

Guidance on cleaning the flame sensor rod for IPI systems.

Checking Flame Patterns, Flame Height

How to visually inspect flame patterns for proper operation.

Checking Vent System

Instructions for inspecting the vent system for obstructions and function.

Cleaning Glass Door

Steps for cleaning the glass door after initial use and as needed.