EasyManua.ls Logo

Heat Siphon Z700HP - User Manual

Default Icon
72 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
i
Copyright 2019 United States ThermoAmp Inc. ALL RIGHTS RESERVED
Publisher: United States ThermoAmp Inc.
1223 Heat Siphon Lane , Latrobe, Pa. 15650
724-537-3500
Owner’s Manual
with Installation & Troubleshooting Instructions
For Heat Siphon® Swimming Pool Heat Pumps
All Z & C Series Heat Siphon Models including
220Volt -1 Ph-60 Hz ONLY: C200HP, C250HP, C375HP, C575HP, Z250HP, Z375HP , Z575HP, Z700HP
220Volt -1 Ph-50 Hz ONLY: C200HP50, C250HP50, C375HP50, C575HP50, Z250HP50, Z375HP50 , Z575HP50
220Volt -3 Ph-50/60 Hz: C250HP3, C375HP3, C575HP3, Z250HP3, Z375HP3 , Z575HP3, Z700HP3
380/460 Volt - 3 Phase - 50/60 Hz - C200HPX, C250HPX, C375HPX, C575HPX, Z250HPX, Z375HPX, Z575HPX, Z700HPX
440 Volt - 3 Phase - 60Hz - C575HP4, Z575HP4, Z575HP4, Z700HP4
200,375,575 Series Heat Only Models 575HC and 700HP Series Models

Table of Contents

Questions and Answers

  • E
    Edward NorrisAug 10, 2025
    What to do if my Heat Siphon Z700HP Heat Pump is leaking water?
    • K
      kylegibsonAug 10, 2025
      First, determine if the leaking water is normal condensation. Condensation occurs as the unit cools off warm, humid air. To resolve this, turn off your Heat Siphon, keep your pool pump on, and wait until the basepan empties. If the basepan doesn't empty but the leaking stops, it's still condensation, but your drain is blocked. Unclog the barb drain fitting and/or replace the vinyl drain tubing. Test the leaking water for chlorine. If it tests negative, it's condensation. If the water has chlorine and the leak continues, contact your dealer.
  • J
    Johnathan EllisAug 17, 2025
    Why my Heat Siphon Z700HP does nothing?
    • A
      Alice BuckleyAug 17, 2025
      Several factors could cause this. The air temperature might be too cold; if it's below approximately 42°F, the unit will shut off automatically to prevent icing. Wait for the air temperature to reach 45°F to 48°F for the unit to automatically reset and turn on. Alternatively, a brief power interruption might have activated a time delay. Wait 5 minutes for the unit to restart. Also, check if the breaker is tripped, which could indicate a bad breaker, faulty wiring, loose wires, or a poor connection in the junction box. Have your installer check the wiring and breaker.
  • M
    Mark LuceroAug 25, 2025
    What to do if my Heat Siphon Z700HP tries to start then does nothing?
    • D
      Daniel DanielAug 26, 2025
      This issue can arise from a few causes. A brief power interruption might have activated the time delay. In that case, wait 5 minutes for the unit to restart. If the air temperature is below 45°F to 48°F and the pool water is cold, wait for both to reach 50°F for the unit to restart automatically and resume normal heating. Also, ensure the pool filter is clean and the pool water flow is stable; restore the correct water flow if needed.
  • K
    Kathy CameronSep 1, 2025
    How to troubleshoot a Heat Siphon Z700HP that runs but doesn't heat?
    • M
      Mary ReedSep 1, 2025
      Several factors could be at play. Check if the air leaving the unit is colder than usual. Also, ensure the pool pump is running long enough each day; run it continuously for 24 hours to determine the required time. If it's still not heating, contact your dealer. Consider whether there's abnormally high heat loss, such as no cover on an extremely windy day. Cover the pool and run the pool pump for 24 hours. If it's still not heating, contact your dealer.

Summary

Owner Section Overview

How Heat Siphon Works

Explains the basic operational principle of the Heat Siphon heat pump.

Exterior Parts Identification

Identifies the various external components and parts of the Heat Siphon unit.

Use a Qualified Installer

Emphasizes the importance of using a qualified professional for installation.

Plan Your Installation

Outlines key considerations and steps for planning the installation process.

Pool Heating Considerations

Discusses important factors for effective pool heating.

Owner Troubleshooting

Offers guidance for common issues faced by Heat Siphon owners.

Maintenance & Winterizing

Covers routine maintenance and seasonal winterization procedures.

Installer Section

Receiving Shipment & Handling

Instructions for inspecting and handling shipments of the unit.

Planning Installation Details

Critical steps and considerations before beginning the installation process.

Wiring Requirements

Details the electrical wiring requirements and code compliance.

Special Installations

Addresses unique installation scenarios and considerations.

Plumbing and Final Wiring

Instructions for completing plumbing connections and final wiring.

Unit Operation & Controls

Initial Start-up Procedures

Step-by-step guide for the initial startup of the Heat Siphon unit.

Digital Player Controls

Details the operation of the digital controller and display.

Analog TimerStat Pro Controls

Details the operation and features of the analog controller.

Technical Appendices

Wiring Diagrams

Contains detailed wiring diagrams for various Heat Siphon models.

Model Specifications

Provides detailed technical specifications for all Heat Siphon models.

Available Accessories

Lists and describes optional accessories for the Heat Siphon.

SPA; HOT TUB Heating Issues

Addresses safety and operational issues specific to spa heating.

USA Warranty Certificate

Details the limited factory warranty terms and conditions.

Heat Siphon Z700HP Specifications

General IconGeneral
ModelZ700HP
CategoryHeat Pump
Phase1
Frequency60 Hz
RefrigerantR-410A
Compressor TypeScroll
Maximum Current30 A
Voltage230V

Related product manuals