Heathkit IM-16 - Page 15

CABLE
ASSEMBLY
WIRING
Connect
the
wires
from
breakout
#5 as
follows:
Refer
to
Pictorial
? for the following
steps.
(
)
Gray to
lug 3
of
control
B
(S-1).
NOTE:
In the
followingsteps,thecableassembly
(
)
White-red
to
lug 2 of control
B
(S-1).
wires will
be connected
to
components
that are
mounted
on
the
subpanel.
Notice that the
cable
(
)
Wtrite-orange
to
lug b of control
B
(S-1).
assembly
has various colored
wires
from each
of
the ten
breakouts.
Breakout#l has nine wires.
Refer to
the
Pictorial
for the
position
ot
;i*"
(
)
White-brown
to
lug
4
of control B
(NS).
and
location of connections'
(
)
Either
white-blue to
lug z
of
terminal
strip
A
(S-2).
connect
the wires
from
breakout
#1
as
follows:
(
)
other
white-blue
to lug 1
of
terminal
(
)
white-orange
to
lug 1
of control
J
(s-1).
strip
A
(s-2)'
(
)
white-yeltow
to
lug
2
of controt J
(s-2).
:""?:ir""t-t1,"
wires
from
breakout
#6 to
control c
L.
(
)
White-red
to
lug 3
of
control
J
(S-1).
(
)
Orange
to
lug
Z
(S_1).
(
)
lvtrlte-green
to L1-5
(s-1).
(
)
Both
viotet to
lug B
(s_z).
(
)
Black
to L3-4
(S-1).
(
)
Orange to
L3-5
(S-1).
Be sure to
solderthe
wire
to both the
front and
rear
lugs
on
wafer
3.
(
)
violet
to L3-6
(s-2).
The green
and
blue
wires from breakout
#1
and the
white-yellow wire from
breakout #2
will
be connected
later.
connect
the
wires
from
breakout
#B as
fo[ows:
H"Jai:?]the
remainingbreakoutswillbecon-
(
)
Brown
to
L3-12
(S-1).
(
)
Red
to L3-3
(S-1).
Connect
the
wires
from breakout
#4 as
follows:
(
)
Both
blue wires to
lug
1
of control
H
(S-2).
(
)
Green
to
lug 2
of controt
H
(S-1).
(
)
Yellow
to
lug
3
of control
H
(S-1).
The gray
wire
and the
white-brown
wire
from
breakout
#4 will
be
connected
later.
Connect
the
wires
from
breakout
#? tocontrolD
as
follows:
(
)
Brown
to
lug 2
(S-1).
(
)
Viotet
to
lug
3
(S-1).
The yellow
wire
andthe
white wire from
breakout
#? will
be connected
later.
(
)
Connect
the white-greenwirefrombreakout
#8 to
switch
M2-9
(S-3).
(
)
Connect
the
lead
from the
positive
(+)
end
of
a
10
trlfd
electrolytic
capacitor
to
lug
1
of
phone
jack
G
(S-2).
Connect
the
other
lead
to
lug
4
of
control
B
(S-2).
(
)
Carefully
examine all
connections.
Every
lug
that
has
a
wire
or
lead attached to
it
should
have been soldered. There
shouldbe
no
blank lugs
on
wafers
trZ,and3
of
switch
L,
or on
waJers
1 and 2
of switch
M. No
connections
should have been made to any
of
the
lugs
on
the
end
wafers
of
any switch.
(
)
Set the
front
panel
assembly
aside,