To Next PageTo Next PageWhat to do if my Heidolph Laboratory Equipment unit cannot be switched on?
If your Heidolph Laboratory Equipment unit won't switch on, there are a couple of things to check: * Make sure the main plug is properly connected to the power supply. * Inspect the fuses; if they are defective or blown, replace them.
Why is there no heating function in my Heidolph Laboratory Equipment?
If there is no heating function in your Heidolph Laboratory Equipment, consider the following possible causes: * The master switch may be deactivated. If so, activate the main switch. * The connecting cable of the heating bath may not be connected. Connect the connecting cable of the heating bath. * The maximum temperature limiter may have responded. If the medium was in the heating bath: Let the heating bath cool and re-set the maximum temperature limiter.
What to do if the motor lift is not functioning in my Heidolph Hei-VAP Advantage?
If the motor lift isn't working on your Heidolph Laboratory Equipment, try these: * Ensure the master switch is activated. * If the lift is at the end stop, activate the other arrow key.
What to do if the drive unit is not rotating in my Heidolph Laboratory Equipment?
If the drive unit isn't rotating on your Heidolph Laboratory Equipment, here's what you can check: * Make sure the speed controller is not on the left stop. If it is, turn the speed controller to the right.
General| Type | Rotary Evaporator |
|---|---|
| Heating Bath Volume | 5 L |
| Display | Digital |
| Stroke | 150 mm |
| Rotation Speed | 20 to 280 rpm |
| Timer | Up to 99 min |
| Voltage | 230 V |
| Dimensions (W x D x H) | 400 x 600 x 600 mm |
Defines signal words and symbols used to indicate risks and precautions.
Provides general safety advice and compliance information for the device.
Defines the intended applications and limitations of the rotary evaporator.
Outlines the operator's duties for safe installation and operation of the unit.
Details the responsibilities of personnel operating the rotary evaporator.
Specifies that only qualified and trained personnel should operate the device.
Lists additional safety features for the evaporator flask, drive motor, and glassware.
Highlights potential residual risks like unintentional rotation, slipping, hot surfaces, and glass breakage.
Covers risks from malfunctions, unauthorized access, and operational noise.
Details risks of injury, mortal danger, fire, and explosions.
Emphasizes safe working practices and adherence to regulations.
Warns about electrical and mechanical hazards and maintaining safe distances.
Prohibits use in explosion-prone areas due to lack of ATEX protection.
Lists and describes the safety features integrated into the heating bath and base unit.
Basic steps for operating the unit and understanding the control panel interface.
Details on operating range and using specific heat transfer fluids.
Details on vacuum control settings and softkey functions.
Explains configuration for easy handling and common temperatures.
Explains final pressure settings and pump type adjustments.
Menu structure for Auto accurate mode, including heating bath, rotation, and distillation rate.
How to fill and set the temperature of the heating bath.
Menu structure for setting pressure, rotation, vacuum, and timer.
Details the advantages of auto accurate mode for precise distillation.
Menu structure for setting heating bath, rotation, timer, and pump type.
Step-by-step guide to calibrate the vacuum sensor for accurate readings.
Accessing the sub-menu for pressure sensor calibration.
Lists common errors and their remedies for units that cannot be switched on or lack heating.
Lists common errors and remedies for drive unit, motor lift, and evacuation issues.
Lists errors related to temperature sensors and transportation protection.
Lists errors related to vacuum valve, vacuum pump, and rotation drive.
Instructions to reset the maximum temperature limiter after an overheat event.
Guidelines for connecting the unit to power and handling fuses safely.
Explains electrical connection color codes and country-specific plugs.
Warnings and precautions regarding glass breakage.
Safety checks and instructions for connecting the base unit and heating bath to power.
Detailed steps for connecting the heating bath cable and power supply.
Safety precautions for the base unit regarding chemicals and atmosphere.
Safety warning about unintentional rotation and hand injuries.
