Home
Henny Penny
Oven
FlexFusion FPE-615
Henny Penny FlexFusion FPE-615 User Manual
5
of 1
of 1 rating
124 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
Model
FPE-
615
FPG-
615
FPE-
621
FPG-
621
FPE-
115
FPG-
115
FPE-
121
FPG-
121
FPE-
215
FPG-
215
FPE-
221
FPG-
221
Service in-
structions
FlexFusion® ELECTRIC
& GAS PLATINUM
COMBI
Translation from the original document •
FM06-101A
DE • 8/26/2019
FM06-101A
en-US
2
Table of Contents
Default Chapter
3
Table of Contents
3
1 Password Overview
7
2 Introduction
8
About this Manual
8
Warranty
8
3 Safety Instructions
9
4 Description of Operation
10
Dynasteam
10
Waveclean
11
5 Opening and Closing the Unit
13
Control Panel
13
Opening the Control Panel
13
Closing the Control Panel
13
Side Wall
14
Removing the Side Wall
14
Attaching the Side Wall
14
6 Component Overview
15
Platinum Operating Panel / Control
15
Gold Operating Panel / Control
16
FGE/ FPE 6Xx 1Xx Electric, Left Side
17
FGE/ FPE 2Xx Electric, Left Side
19
FGG/ FPG 6Xx 1Xx Gas, Left Side
20
FGG / FPG 2Xx Gas, Left Side
22
FGG/ FPG 6Xx 1Xx, Right Side
24
FGG/ FPG 2Xx, Right Side
25
7 Service Menu - Appliance Test
26
Service Menu
26
Calling up the Service Level
26
Service Menu Overview
26
Appliance Information
27
Status Information
28
Combidoctor
31
Relay Test
34
Waveclean Test
36
100°C + Core Temperature Calibration
37
Checking the Calibration - Single-Chamber Appliance 6.X / 10.X
38
Checking the Calibration - Two-Chamber Appliance 20.X
39
Calibrating the Cooking Chamber Sensor - Single-Chamber Appliance 6.X / 10.X
40
Calibrating the Cooking Chamber Sensor - Two-Chamber Appliance
41
Dynasteam Test
42
Emptying the Water
43
Data and Time
43
Installation Height
44
Audio Settings
44
Select Signal Tones
45
POS Activation (Only for Electric Energy Type)
45
Exporting Log Data
45
Software Update
46
Importing Additional Content
46
Restoring Data
47
Backing up Data
47
Water Filter Maintenance
48
Importing Contact Data
48
Setting Units
49
Backup Relay
49
Settings Parameters
51
Selecting and Changing Parameters
51
Parameter Overview
51
Backing up the SD Card
53
Restoring the SD Card
53
Background Lighting
54
Hour Meter
54
Status Overview Direct Access
54
8 Software
55
Software Update
55
Importing Additional Content
57
Importing the Manufacturer's Cookbook
59
9 Trade Show Mode
61
10 Electronics
62
Overview of the Controller
62
Layout of the Control Board
63
Configuration of the Control Board
64
Safety Overview
66
11 Gas Technology
68
Basic Principles
68
CO2 Setting
69
Opening the Setting Menu
69
Adjusting the Settings (CO2 Calibration)
70
Converting the Gas Type
76
Checking the Connection Pressure
78
Checking the Offset Pressure
80
12 Gas Orifices and C02 Values up to S/N 16212355
82
13 Gas Orifices and C02 Values after S/N 16212356
83
14 Fault Messages & Troubleshooting
84
Overview
84
Symbols for Errors
85
Emergency Operation
87
Temperature Sensor Area
88
Cooking Chamber Sensor Defective (694, 695)
88
Top Cooking Chamber Sensor Defective (696, 728)
89
Bottom Cooking Chamber Sensor Defective (697, 729)
90
Core Temperature Sensor Defective (699, 700)
91
Internal Core Temperature Sensor Defective (714, 716)
92
External Core Temperature Sensor Defective (715, 717)
92
Water Vapor Sensor Defective (710)
93
Siphon Temperature very High (SOF_ID20, ID21)
94
Risk of Frost (TMP_ID72, MMI_ID51)
94
Excess Temperature in the Cooking Chamber (ID18, ID73)
95
Motor Area
96
Overview
96
Fan Defective or Temperature Limiter Triggered (702)
98
Fan Defective. Cooking Program was Cancelled (701)
100
Top Fan Defective. Automatic Switching to Emergency Operation (703, 705)
100
Bottom Fan Defective. Automatic Switching to Emergency Operation (704, 706)
101
FAN_ID23: Fan Error: Attempt to Restart
103
FAN_ID24: Upper Fan Fault: Attempt to Restart
103
FAN_ID25: Lower Fan Fault: Attempt to Restart
103
Water Area
105
Water Pressure too Low (709)
105
Water Pressure During Waveclean too Low
107
Electronics / Control Area
108
Overtemperature Control (TMP_ID2)
108
Critical Temperature in the Electronics (MMI_ID50)
109
Failure to Access External EEPROM (SOF_ID12)
110
Faulty CAN Connection
110
5007: Not Enough Storage Space for Software Update
110
5008: no New Version Found
110
5009: the Application Could Not be Started. Application Is Restarting
111
5010: the Application Could Not be Started. Restore Configuration Backup
111
5013: Application Could Not be Restored! Restore to Factory Settings with OK
111
Unit was Restarted after Power Failure
112
Door Is Open - Cooking Program was Stopped
112
Gas Area
114
No Gas (OTH_ID1)
114
No Gas (Top)(OTH_ID2)
116
No Gas (Bottom)(OTH_ID3)
116
No Flame (OTH_ID4)
116
No Flame (Top)(OTH_ID5)
116
No Flame (Bottom)(OTH_ID6)
117
Communication Fault between I/O and Ignition Electronics (OTH_ID25)
117
Communication Fault between I/O and Ignition Electronics (Top)(OTH_ID26)
118
Communication Fault between I/O and Ignition Electronics (Bottom) (OTH_ID27)
118
GAS_ID13: Flame Fault During Operation
119
Testing the Gas Components
119
Checking the Electrodes
119
Inspection of the Gas Solenoid Valve
120
Testing the Heat Exchanger
121
Other manuals for Henny Penny FlexFusion FPE-615
Installation Manual
56 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Henny Penny FlexFusion FPE-615 and is the answer not in the manual?
Ask a question
Henny Penny FlexFusion FPE-615 Specifications
General
Brand
Henny Penny
Model
FlexFusion FPE-615
Category
Oven
Language
English
Related product manuals
Henny Penny FlexFusion FGE 615
84 pages
FlexFusion ELECTRIC SPACESAVER PLUS FSE-610
72 pages
Need help?
General
To Next Page
