Why does my Heta Wood stove smell and the surface steams?
If your Heta Wood stove smells and the surface is steaming, it's because the paint on the stove surface is not yet fully hardened. Ensure there is sufficient ventilation.
Why does my Heta Scan-Line 900 burn poorly and the glass soots up?
Poor burning and sooty glass in your Heta Wood stove can be due to several factors: * Inadequate chimney draft: Improve the chimney draft. * Insufficient air supply: Refer to the operating instructions for proper usage. * Damp wood: Ensure firewood is dried for at least one year after splitting. * Firewood pieces too large: Use smaller pieces of firewood. * Insufficient air supply to the room: Open windows or clean the outdoor air connection, depending on the cause (range hoods, airtight windows, etc.).
Why does my Heta Wood stove 'clunk'?
The 'clunking' sound in your Heta Wood stove is usually due to tension in the metal plates. Adjust the metal plates to resolve this.
Why is there condensation in the combustion chamber of my Heta Wood stove?
Condensation in the combustion chamber of your Heta Wood stove can be due to: * Moisture in the vermiculite: This evaporates by itself after the stove has been lit a few times. * Damp wood: Use dry firewood.
When should I replace the vermiculite in my Heta Wood stove?
Normal wear and minor cracks in the vermiculite of your Heta Wood stove are of no significance. It should be replaced when the steel of the combustion chamber is visible.
Is it normal for the vermiculite in my Heta Scan-Line 900 Wood stove to be cracked?
Cracks in the vermiculite of your Heta Wood stove's combustion chamber are usually cosmetic and caused by shocks or impacts while adding firewood. It should be replaced when the steel of the combustion chamber is visible.
Why is there condensation from the flue pipe of my Heta Scan-Line 900 Wood stove?
Condensation from the flue pipe of your Heta Wood stove can occur because: * The pipe is too long or the chimney is too cold: Improve the flue pipe and insulate the chimney. * Damp wood: Use dry firewood.
What does it mean if steel surfaces in my Heta Wood stove's combustion chamber have oxidised?
Oxidation of steel surfaces in the combustion chamber of your Heta Wood stove indicates that the temperature inside is too high. If there are clear cracks or weaknesses in the stove body, it must be replaced.
How to fix a whistling Heta Scan-Line 900?
If your Heta Wood stove is whistling, it's likely due to too much chimney draft. Install a damper to resolve this issue.
Why does my Heta Wood stove burn poorly after warm-up and the glass soots up?
If your Heta Wood stove burns poorly after the warm-up phase, and the glass slowly soots up, it could be due to soot in the flue pipe. Clean the flue pipe regularly, limit the use of horizontal flue pipes, and avoid using firewood that generates large quantities of ash.
General| Brand | Heta |
|---|---|
| Model | Scan-Line 900 Series |
| Category | Wood stove |
| Language | English |
Instructions and illustrations for safely unpacking the wood stove.
Overview of items found with the stove and optional accessories.
Prerequisites and checks before initial operation of the wood stove.
Guidance on the initial lighting and curing of the stove's paint.
How to adjust the air control for optimal combustion.
Step-by-step instructions for safely lighting the wood stove.
Best practices for adding wood to maintain the fire.
Procedure for safely removing ash from the stove.
How to achieve lower heat output and manage slow burning.
Critical safety warning regarding potential explosion hazards.
Factors affecting chimney draft and their impact on stove performance.
Guidelines on suitable types of wood and how to prepare them for burning.
Common issues encountered during operation and their potential causes.
Steps to take in case of a chimney fire and post-incident inspection.
General care and cleaning instructions for the stove's exterior.
How to clean soot build-up from the stove's glass door.
Instructions for cleaning the baking oven racks and rails.
A comprehensive table listing faults, causes, troubleshooting steps, and solutions.
A visual guide detailing maintenance tasks and their recommended frequency.
Information about the product warranty, coverage, and claim procedures.
Step-by-step guide on using graphite spray for lubricating moving components.
Instructions for cleaning fire bricks and related components in the Scan-Line 900 series.
Instructions for cleaning fire bricks in the Scan-Line 900 Side windows series.
Table listing technical specifications, clearances, and fuel data for the stove.
Exploded view and part list for the internal fire chamber of the Scan-Line 900 series.
Exploded view and part list for the internal fire chamber of the Side windows series.
Detailed breakdown of the stove's door components and their part numbers.
Detailed breakdown of the glass door components and their part numbers.
Detailed breakdown of the baking oven door components and their part numbers.
General guidance and requirements for installing the wood stove.
Specifies minimum safe distances to combustible and non-combustible materials.
Requirements for the floor supporting the stove, including non-combustible materials.
Guidelines for connecting the stove to the chimney system.
Information on providing adequate air for combustion and room ventilation.
Technical drawings and measurements for different stove models.
Instructions for assembling the thermal stones within the stove.
How to connect an external air supply to the stove.
Instructions for installing the HAC (Heat Accumulation) unit.
Detailed clearance requirements for installation according to EN 13 240 standards.
Steps for modifying the stove to use a back flue outlet.
Information on adjusting the door stop for proper functionality.
Information regarding smoke control areas and appliance suitability.
Official declaration of compliance with EU harmonized regulations for the stove.
Official declaration of compliance with EU harmonized regulations for the stove.
To Next Page
