What to do if the Hewlett Packard Enterprise Controller power supply PCM OK LED is off?
If the power supply module is not receiving adequate power, verify that the power cable is properly connected and check the power source. Also, verify that the PCM is firmly locked into position within the PCM slot. Review event logs for specific information regarding a PCM fault and follow any recommended actions.
What to do if the Hewlett Packard Enterprise Controller connected host port Host Link Status LED is off?
If the link is down, check cable connections and reseat if necessary. Inspect cables for damage and replace if necessary. Swap cables to determine if the fault is caused by a defective cable and replace the cable if necessary. Verify that the switch, if any, is operating properly. If possible, test with another port. Verify that the HBA is fully seated, and that the PCI slot is powered on and operational. Review event logs for indicators of a specific fault in a host data path component and follow any recommended actions.
What to do if the Hewlett Packard Enterprise HPE MSA 1060 Controller connected port Network Port Link Status LED is off?
If the link is down, check cable connections and reseat if necessary. Inspect cables for damage and replace if necessary. Swap cables to determine if the fault is caused by a defective cable and replace the cable if necessary. Verify that the switch, if any, is operating properly. If possible, test with another port. Verify that the HBA is fully seated, and that the PCI slot is powered on and operational. Review event logs for indicators of a specific fault in a network component and follow any recommended actions. Use standard networking troubleshooting procedures to isolate faults on the network.
What does it mean if the Hewlett Packard Enterprise Controller enclosure front panel Fault/Service Required LED is amber?
If a fault condition exists or occurred, check the LEDs on the back of the controller enclosure to narrow the fault. Check the event log for specific information regarding the fault and follow any recommended actions. If installing an IOM FRU, try removing and reinstalling the new IOM and check the event log for errors. If the above actions do not resolve the fault, isolate the fault.
What to do if the Hewlett Packard Enterprise HPE MSA 1060 Controller connected host port Expansion Port Status LED is off?
If the link is down, check cable connections and reseat if necessary. Inspect cables for damage and replace if necessary. Swap cables to determine if the fault is caused by a defective cable and replace the cable if necessary. Review event logs for indicators of a specific fault in a host data path component and follow any recommended actions.
What to do if the Hewlett Packard Enterprise HPE MSA 1060 Controller enclosure rear panel Fault/Service Required LED is amber?
If a hardware-controller power-up error, cache flush error, or cache self-refresh error occurred, restart the controller from the other controller using the SMU or CLI. If the above action does not resolve the fault, remove the controller module and reinsert it.
What to do if the Hewlett Packard Enterprise HPE MSA 1060 enclosure rear panel FRU OK LED is off?
If the controller module is not powered on or has failed, verify the controller module is fully inserted and latched in place, and that the enclosure is powered on. Check the event log for specific information regarding the failure.
How to correct enclosure IDs on a Hewlett Packard Enterprise HPE MSA 1060 Controller?
To correct enclosure IDs, make sure that both controllers are up, and perform a rescan using the SMU or the CLI.
How to stop I/O on a Hewlett Packard Enterprise Controller?
To stop I/O, stop I/O to all volumes in the pool with the affected disk group, from all hosts and remote systems as a data protection precaution. It is also recommended to conduct regularly scheduled backups of your data.
Describes the different MSA storage enclosure configurations and disk support.
Explains the SMU and CLI as management interfaces for enclosures.
Details the host interface protocols supported by controller modules.
Describes the front panel elements, including bezels and LEDs.
Details the types of disks supported by MSA 2060 and MSA 1060 enclosures.
Outlines the sequential steps for installing enclosures and initial configuration.
Explains requirements and considerations for using Full Disk Encryption (FDE).
Describes cabling requirements for connecting controller and disk enclosures.
Provides the procedure for powering the storage system on and off.
Details the requirements for data hosts connecting to the storage system.
Explains Fibre Channel, iSCSI, and SAS protocols for host connections.
Defines initiators and describes direct attach and switch-connect configurations.
Introduces the CLI port for direct system configuration and management.
Explains the serial port emulation for connecting to the CLI via USB.
Details steps for preparing a Linux system to connect to the CLI port.
Details steps for preparing a Windows system to connect to the CLI port.
Describes methods for obtaining and setting IP addresses for network ports.
Guides on accessing the web-based Storage Management Utility (SMU).
Explains how to configure and provision the storage system using the SMU.
Addresses issues with connecting to the controller via the USB CLI port.
Presents the basic methodology for locating faults within the storage system.
Lists options like SMU, CLI, and LEDs for fault isolation.
Details gathering fault info, determining fault location, and reviewing logs.
Provides contact information and resources for technical support.
Guides on how to download and install software and firmware updates.
Describes front panel LEDs for enclosures, including bezel and hubcaps.
Details rear panel LEDs for controller modules (FC, iSCSI, SAS) and PCMs.
Describes rear panel LEDs for expansion modules and drive enclosures.
Outlines safety precautions for system installation and handling.
Provides guidelines for selecting an installation site and preparing the environment.
Details requirements for AC power supply, wiring, and connections.
Details requirements for DC power supply, wiring, and connections.
Provides guidelines for lifting and handling enclosures based on weight.
Outlines electrical precautions and considerations for system installation.
Specifies minimum clearances for adequate airflow and cooling.
Provides guidelines for routing and managing power and interface cables.
Details requirements for the management host used for initial setup.
Specifies dimensions and weights for rackmount enclosures.
Lists technical specifications for operating and non-operating environments.
Lists precautions to prevent damage from static electricity.
Describes various methods for grounding ESD-sensitive parts.
Guides on how to locate and enable SAS fanout cable support using the SMU.
General| Controller Type | Dual Controller |
|---|---|
| Maximum Drives Supported | 96 |
| Supported Drive Types | SAS, SATA |
| RAID Levels | 0, 1, 5, 6, 10 |
| Form Factor | 2U |
| Processor | Dual-core 1.2 GHz |
To Next Page
