What to do if the Hewlett Packard Enterprise Controller power supply PCM OK LED is off?
If the power supply module is not receiving adequate power, verify that the power cable is properly connected and check the power source. Also, verify that the PCM is firmly locked into position within the PCM slot. Review event logs for specific information regarding a PCM fault and follow any recommended actions.
What to do if the Hewlett Packard Enterprise HPE MSA 2060 connected host port Host Link Status LED is off?
If the link is down, check cable connections and reseat if necessary. Inspect cables for damage and replace if necessary. Swap cables to determine if the fault is caused by a defective cable and replace the cable if necessary. Verify that the switch, if any, is operating properly. If possible, test with another port. Verify that the HBA is fully seated, and that the PCI slot is powered on and operational. Review event logs for indicators of a specific fault in a host data path component and follow any recommended actions.
What to do if the Hewlett Packard Enterprise Controller connected port Network Port Link Status LED is off?
If the link is down, check cable connections and reseat if necessary. Inspect cables for damage and replace if necessary. Swap cables to determine if the fault is caused by a defective cable and replace the cable if necessary. Verify that the switch, if any, is operating properly. If possible, test with another port. Verify that the HBA is fully seated, and that the PCI slot is powered on and operational. Review event logs for indicators of a specific fault in a network component and follow any recommended actions. Use standard networking troubleshooting procedures to isolate faults on the network.
What does it mean if the Hewlett Packard Enterprise Controller enclosure front panel Fault/Service Required LED is amber?
If a fault condition exists or occurred, check the LEDs on the back of the controller enclosure to narrow the fault. Check the event log for specific information regarding the fault and follow any recommended actions. If installing an IOM FRU, try removing and reinstalling the new IOM and check the event log for errors. If the above actions do not resolve the fault, isolate the fault.
What to do if the Hewlett Packard Enterprise Controller connected host port Expansion Port Status LED is off?
If the link is down, check cable connections and reseat if necessary. Inspect cables for damage and replace if necessary. Swap cables to determine if the fault is caused by a defective cable and replace the cable if necessary. Review event logs for indicators of a specific fault in a host data path component and follow any recommended actions.
What to do if the Hewlett Packard Enterprise HPE MSA 2060 Controller enclosure rear panel Fault/Service Required LED is amber?
If a hardware-controller power-up error, cache flush error, or cache self-refresh error occurred, restart the controller from the other controller using the SMU or CLI. If the above action does not resolve the fault, remove the controller module and reinsert it.
What to do if the Hewlett Packard Enterprise HPE MSA 2060 Controller enclosure rear panel FRU OK LED is off?
If the controller module is not powered on or has failed, verify the controller module is fully inserted and latched in place, and that the enclosure is powered on. Check the event log for specific information regarding the failure.
How to correct enclosure IDs on a Hewlett Packard Enterprise Controller?
To correct enclosure IDs, make sure that both controllers are up, and perform a rescan using the SMU or the CLI.
How to stop I/O on a Hewlett Packard Enterprise Controller?
To stop I/O, stop I/O to all volumes in the pool with the affected disk group, from all hosts and remote systems as a data protection precaution. It is also recommended to conduct regularly scheduled backups of your data.
Describes the MSA 1060/2060/2062 storage enclosures and disk configurations.
Outlines the steps for installing enclosures and initial configuration.
Details cabling requirements for connecting controller and disk enclosures.
Provides procedures for powering the system on and off.
Lists requirements for data hosts connecting to MSA storage systems.
Instructions on how to access the Storage Management Utility.
Guides on configuring and provisioning the storage system.
Outlines the basic methodology for isolating faults within the storage system.
Details troubleshooting steps for host connection issues with FC and iSCSI ports.
Precautions to prevent damage from static electricity when handling components.
Methods for grounding equipment to prevent ESD damage.
General| Maximum Number of Drives | 192 |
|---|---|
| RAID Levels | 0, 1, 5, 6, 10, 50, 60 |
| Form Factor | 2U |
| Controller Type | Dual controller |
| Host Connectivity | iSCSI, Fibre Channel |
| Supported Drive Types | SAS, SATA |
| Management Interface | CLI |
| Product Type | Storage Controller |
| Data Transfer Rate | 12 Gbps SAS |
| Host Interface | SAS, Fibre Channel, iSCSI |
| Drive Bays | 24 |
| Power Supply | Dual redundant power supplies |
To Next Page
