EasyManua.ls Logo

Hifonics Zeus ZRX3200.1D User Manual

Hifonics Zeus ZRX3200.1D
14 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
ZRX500.2 / ZRX1200.2
ZRX600.4 / ZRX1000.4 / ZRX2000.4
ZRX1200.1D / ZRX1800.1D / ZRX2400.1D / ZRX3200.1D
Question and Answer IconNeed help?

Do you have a question about the Hifonics Zeus ZRX3200.1D and is the answer not in the manual?

Hifonics Zeus ZRX3200.1D Specifications

General IconGeneral
Channels1
Power Output (RMS)3200W
Power Output (Peak)6400W
Frequency Response10 Hz - 250 Hz
Signal-to-Noise Ratio>95dB
Damping Factor> 200
Minimum Impedance1 Ohm
Input Voltage6V - 0.2V
Bass Boost0 - 18 dB
Subsonic Filter10 Hz - 50 Hz
Low Pass Filter35Hz - 250Hz
Fuse Rating300A
Phase Shift0 - 180 Degrees
RMS Power at 1 Ohm3200W
RMS Power at 4 Ohms800W
Input Sensitivity0.2V - 6V
RMS Power at 2 Ohms1600 Watts

Summary

General Installation Procedure

Amplifier Feature Descriptions

Zeus ZRX Amplifiers Overview

General description of the Zeus ZRX series amplifier capabilities and features.

2-Channel Amplifier Features

Details on features and controls for the 2-channel Zeus ZRX amplifiers.

4-Channel Amplifier Features

Details on features and controls for the 4-channel Zeus ZRX amplifiers.

1-Channel Mono D-Class Amplifier Features

Details on features and controls for the 1-channel Zeus ZRX mono amplifiers.

2-Channel Amplifier Applications

Full Range Stereo Application

Describes the basic full-range stereo setup for 2-channel amplifiers.

Mono Bridging Application

Illustrates the mono bridging method for 2-channel amplifiers.

4-Channel Amplifier Applications

4 Channel Full Range System

Shows how to use 4-channel amps as discrete full-range units.

2 or 3 Channel System Setup

Explains creating a 3-channel system by mono bridging channel pairs.

4-Channel Amplifier Advanced Applications

Front/Rear High Pass with Mono Sub Bass

Shows system setup with a 4-channel for highs and a 2-channel for mono sub.

1-Channel Amplifier Applications

Basic 1-Channel Application

Describes the fundamental setup for 1-channel mono D-class amplifiers.

Setting Up Systems for Best Performance

Troubleshooting a System

Protect System Description

Explanation of the PROTECT system and its indicators for amplifier faults.

Amplifier Heatsink Overheating

Causes and solutions for amplifier overheating shutdown.

Low Output Power Issues

Troubleshooting steps for reduced amplifier output power.

Fuse Blowing Causes

Identifies common reasons for amplifier fuses blowing.

System Does Not Turn On

Steps to diagnose why the audio system fails to power on.

Noise Problems

Categorization and troubleshooting of system noise and interference.

Hiss or White Noise

Diagnosing and resolving hiss or white noise in the audio system.

Electrical Interference

Identifying and mitigating electrical interference in the car audio system.

Ticking or Whine with Engine RPM

Troubleshooting noise that changes with engine speed.

Constant Whine Diagnosis

Pinpointing and resolving a persistent whine in the audio system.

Maxxsonics Limited Warranty

MaxxLink Product Information

Maxxtech Technology

Introduction to Maxxtech technology and its role in Maxxsonics products.

MaxxLink Products & Warranty

Overview of MaxxLink product labeling, performance levels, and extended warranty.

Related product manuals