HIKVISION DS-2CE56D1T-IRM - User Manual

TVI Turret Camera
User Manual
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see:
www.recyclethis.info.
2006/66/EC (battery directive):This
product contains a battery that cannot
be disposed of as unsorted municipal
waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
UD.6L0201D1933A01
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
This product and - if applicable - the
supplied accessories too are marked
with "C E" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
TURBO HD
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology It features high resolution,.
low image distortion and low noise, etc , which.
makes it suitable for surveillance system and
image processing system.
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l OSD menu, parameters are configurable;
l Support auto white balance, auto gain control,
Support image effect adjustment;
l
l
Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
1 Introduction
1.1 Product Features
1.2 Overview
1.2.1 Overview of Type I Camera
1.2.2 Overview of Type Camera
II
Enclosure
HD Video Cable
Mounting Base
1.2.3 Overview of Type CameraIII
2 Installation
Before you start:
l Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
l Make sure that all the related equipment is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Check whether the power supply is matched
with your power output to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Installation of Type CameraI
Steps:
1.Drill the screw holes according to the drill
template.
Figure 2-1 The Drill Template
2. Screw the clip plate onto the mounting base
loosely.
Power Cable
HD Video Cable
Mounting Base
Camera
Trim Ring
Enclosure
Power Cable
Camera
Trim Ring
Enclosure
Camera
HD Video Cable
Power Cable
Mounting Base
3. Fix the mounting base to the ceiling with the
supplied screws.
4.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
5.Pull out the clip plate and secure the camera
with the trim ring to the mounting base.
6.Push the clip plate in and tighten the lock screw
to secure the trim ring.
Figure 2-2 Screw the Clip Plate
Clip Plate
Screw hole
Side Opening
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
0100001050409
Please refer to the product specification for
camera parameters and functions.
Type
Type
Type
I
II
Model
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Type
III
DS-2CE56D1T-IRM
DS-2CE56D1T-IT3
DS-2CE56D1T-IR
DS-2CE56D1T-IT1

Summary

Regulatory Information

FCC Information

Details FCC compliance and conditions for digital devices operating in commercial environments.

EU Conformity Statement

Covers CE marking, Low Voltage, EMC, RoHS, WEEE, and battery directives for EU compliance.

Introduction to TVI Turret Camera

Product Features

Highlights high resolution, low illumination, OSD menu, auto white balance, and 3-axis design.

Camera Overview

Illustrates the components of Type I, II, and III cameras, including enclosure, trim ring, and mounting base.

Camera Installation Guide

Pre-Installation Checklist

Essential checks before installation: package condition, power off, product specs, and wall suitability.

Type I Camera Installation

Step-by-step guide for installing the Type I camera, including drilling, base mounting, and securing.

Type II Camera Installation

Detailed steps for installing the Type II camera, covering drilling, base mounting, and cable connections.

Type III Camera Installation

Step-by-step instructions for installing the Type III camera, including drilling, base mounting, and cable routing.

Camera Menu Operation and Settings

Format Settings

Option to set the video output format to PAL or NTSC.

Setup Menu

Enters the sub-menu for camera setup and parameter adjustment.

Auto Exposure (AE) Settings

Adjusts brightness, exposure mode (Globe, BLC), and AGC levels for optimal image quality.

White Balance (WB) Settings

Sets White Balance mode to AWB (automatic) or MWB (manual gain control).

Day & Night Mode Configuration

Configures the camera's day/night mode (COLOR, B/W, SMART) and IR settings.

Video Settings Adjustment

Adjusts video parameters like contrast, sharpness, saturation, DNR, and mirror settings.

Reset to Default Settings

Restores all camera settings to their factory default values.

Save and Exit Menu

Saves the current settings and exits the menu.

HIKVISION DS-2CE56D1T-IRM Specifications

General

Type	CCTV security camera
Day/night mode	Yes
Languages support	CHI (SIMPL), CHI (TR), ENG
Placement supported	Outdoor
Connectivity technology	Wired
Signal-to-Noise Ratio (SNR)	52 dB
Form factor	Dome
Mounting type	Ceiling
Product color	White
International Protection (IP) code	IP66
DC output voltage	12
Power consumption (max)	3 W
Power over Ethernet (PoE)	No
Total megapixels	2 MP
Maximum resolution	1920 x 1080 pixels
Supported video modes	1080p
Analog signal format system	NTSC, PAL
Pan range	0 - 355 °
White balance	Auto, Manual, Push
Tilt angle range	0 - 75 °
Angle of rotation	355 °
Camera shutter speed	1/30 - 1/50000 s
Minimum illumination	0.034 lx
Field of view (FOV) angle	55.4 °
Sensor type	CMOS
Optical sensor size	1/2.7 \
Fixed focal length	6 mm
Maximum aperture number	2.5
LED type	IR
Night vision distance	20 m
Lens mount interface	M12
Number of cameras	1
Operating temperature (T-T)	-40 - 60 °C
Operating relative humidity (H-H)	0 - 90 %

Weight and Dimensions

Depth	89.6 mm
Width	82.6 mm
Height	59.1 mm
Weight	400 g