What to do if The outdoor DC fan motor (down fan motor) fault in Hisense AMW4-36U4RAA?
To address the outdoor DC fan motor fault (down fan motor) in your Hisense Air Conditioner, you can try: * Reconnecting the wiring of the down DC fan motor. * Replacing the down DC fan motor. * Replacing the driver board of the fan motor. * Checking the outdoor fan to ensure it can run normally.
What to do if my Hisense AMW4-36U4RAA has poor cooling/heating?
If your Hisense Air Conditioner is not cooling or heating effectively, start by cleaning the heat exchanger of the outdoor unit, such as the condenser. Ensure there are no heating devices indoors that might be affecting the temperature. Maintain good air tightness indoors by minimizing how often people enter and exit. Check for and remove any obstructions blocking the outdoor heat exchanger. Finally, double-check and reset the temperature to the desired setting.
Why does the compressor of my Hisense Air Conditioner start and stop frequently?
If your Hisense Air Conditioner's compressor starts and stops frequently, it's likely that the air inlet or outlet is blocked. Remove any obstacles to ensure proper airflow.
How to fix water leakage in Hisense AMW4-36U4RAA Air Conditioner?
If your Hisense Air Conditioner is leaking water, the drainage pipe may be blocked or broken, in this case, change drainage pipe. Alternatively, the wrap of the refrigerant pipe joint might not be completely sealed; re-wrap it tightly.
How to fix Discharge temperature sensor fault in Hisense Air Conditioner?
To resolve a discharge temperature sensor fault in your Hisense Air Conditioner, you can try: * Reconnecting the wiring of the discharge temperature sensor. * Replacing the discharge temperature sensor. * Replacing the outdoor control board.
What to do if my Hisense AMW4-36U4RAA shows IPM and control board communication fault?
To address an IPM and control board communication fault in your Hisense Air Conditioner, you can try the following steps: * Reconnect the cable between the control board and the driver board. * Replace the communication cable between the control board and the driver board. * Replace the driver board. * Replace the control board.
How to fix outdoor coil temperature sensor fault in Hisense AMW4-36U4RAA?
To fix an outdoor coil temperature sensor fault on your Hisense Air Conditioner, you can try: * Reconnecting the outdoor coil temperature sensor. * Replacing the outdoor coil temperature sensor components. * Replacing the outdoor control board components.
What to do if my Hisense Air Conditioner shows EEprom Data error?
To address an EEprom Data error in your Hisense Air Conditioner, you can try the following: * Replace the EE components. * Replace the outdoor control board components. * Reassemble the EE components.
What to do if my Hisense AMW4-36U4RAA Air Conditioner shows compressor overheat protector device?
If your Hisense Air Conditioner's compressor is overheating, you can try the following steps: 1. Reconnect the wiring of the overload protector. 2. Replace the overload protector. 3. Check for leakage at the welding points and recharge the refrigerant if necessary. 4. Add refrigerant. 5. Replace the expansion valve. 6. Replace the outdoor control board.
Why does the compressor in my Hisense AMW4-36U4RAA start and stop frequently?
If the compressor in your Hisense Air Conditioner is starting and stopping frequently, it's possible that the air inlet or outlet is blocked. Remove any obstacles that may be causing the blockage.
Specifies the type of air conditioners covered in the manual.
Provides crucial notices regarding product improvement, hazards, and intended use.
Lists electrical specifications like power supply, voltage, frequency, current, and ELB for different models.
Explains that the following charts show outdoor unit capacity based on ambient temperature.
Provides charts illustrating ESP for 9K duct type units at standard and high ESP conditions.
Details the parameters for the outdoor compressor discharge temperature sensor, including resistance values and deviation rates.
Lists common malfunctions, possible reasons, and troubleshooting steps for air conditioners.
Explains how to check fault codes displayed by LED lamps on the outdoor main control board.
Outlines the test system flow for checking the refrigerant system, including pressure tests and refrigerant charging.
Provides model numbers for compressors and explains how to examine and repair them, including resistance tests.
Crucial safety instructions for installers and service personnel regarding safe operation.
Specifies the type of air conditioners covered in the manual.
Provides crucial notices regarding product improvement, hazards, and intended use.
Lists electrical specifications like power supply, voltage, frequency, current, and ELB for different models.
Explains that the following charts show outdoor unit capacity based on ambient temperature.
Provides charts illustrating ESP for 9K duct type units at standard and high ESP conditions.
Details the parameters for the outdoor compressor discharge temperature sensor, including resistance values and deviation rates.
Lists common malfunctions, possible reasons, and troubleshooting steps for air conditioners.
Explains how to check fault codes displayed by LED lamps on the outdoor main control board.
Outlines the test system flow for checking the refrigerant system, including pressure tests and refrigerant charging.
Provides model numbers for compressors and explains how to examine and repair them, including resistance tests.
Crucial safety instructions for installers and service personnel regarding safe operation.
General| Brand | Hisense |
|---|---|
| Model | AMW4-36U4RAA |
| Category | Air Conditioner |
| Language | English |
To Next Page