Hitachi CP-WX8650 User Manual (English)

Questions and Answers:

N
ntaylorAug 17, 2025
Why can't I connect to the Hitachi CP-WX8650 via wired network?
- H
  Haley SimonAug 17, 2025
  There could be several reasons why you can't connect to the projector via a wired network. First, ensure the projector and the network device are turned on. If you intend to use the network function in standby mode, make sure it is set to NORMAL. Verify that the LAN cable is securely connected. If the MAC address on the projector's label doesn't match the one displayed in the NETWORK INFORMATION – WIRED menu, contact your dealer. Check the network settings in the NETWORK INFORMATION – WIRED menu, consulting your network administrator if needed. Ensure that wireless LAN and wired LAN use different network addresses. Finally, refer to your computer's user manual to enable the wired network adapter.
L
Lisa HarrisAug 22, 2025
What to do if Hitachi CP-WX8650 Projector cannot communicate via wireless network with multiple devices?
- C
  Carrie BurnettAug 22, 2025
  If you're experiencing communication issues with multiple devices connected wirelessly to the projector, confirm the number of connected devices. In Simple Access Point mode, the projector supports up to 11 devices. If the maximum number is reached, disconnect a currently connected device before adding another. Ensure that the DHCP setting is enabled on your computer. Also, consider changing the channel setting. If IP address overlaps, turn off your WiFi device and turn it on again.
B
Barbara AllenAug 25, 2025
Why is my Hitachi Projector not displaying Web(Projector Web Control) correctly?
- A
  Austin RodriguezAug 26, 2025
  If the Projector Web Control is not displaying correctly, first, make sure you're entering the projector's IP address into the web browser. Enable JavaScript in your web browser's settings. Note that the recommended web browsers are Internet Explorer 8/9/10/11, and the Projector Web Control may not display correctly in other browsers. Also, try clearing your browser's cache.
J
Joseph ReedAug 27, 2025
How to fix time settings on Hitachi CP-WX8650 Projector?
- S
  Sharon DeleonAug 28, 2025
  If the time settings on your projector are incorrect, consider these steps: Ensure the battery is properly set; if the time is lost soon after setting it, the battery may be exhausted and need replacement. Verify the settings in the Date/Time Settings menu of the Projector Web Control or the DATE AND TIME menu of the projector itself. Connect the projector to the network. Check the settings of the SNTP server, consulting with your network administrator if needed. When obtaining the time via the network, set the correct time difference if the displayed time is inaccurate.
R
Rachel PruittAug 31, 2025
How to fix Crestron e-Control not displaying on Hitachi Projector?
- N
  nconnerAug 31, 2025
  If Crestron e-Control® is not displaying, first, install Adobe® Flash® Player. Ensure you are using a web browser that supports Adobe® Flash® Player. Enable Crestron e-Control® settings on the Network Settings – Other Setup screen of the Projector Web Control. Finally, set Crestron in Projector Web Control - Network Settings - Common Setup to ON.
C
carterchristopherSep 2, 2025
Why can't I use wireless and wired LAN at the same time on my Hitachi CP-WX8650?
- J
  Jim JohnsonSep 2, 2025
  You cannot use wireless LAN and wired LAN at the same time if they have the same network address. Set different network addresses for each. Also, either wired LAN or wireless LAN can access different networks by setting the default gateway of either wired LAN or wireless LAN to 0.0.0.0.
V
Veronica HansenSep 5, 2025
How to troubleshoot schedule not executed correctly on Hitachi CP-WX8650 Projector?
- K
  Kelly BrownSep 5, 2025
  If the schedule is not executing correctly, ensure the projector is turned on. If you want to use the schedule function in standby mode, set the projector to NORMAL. Check the date and time settings. Also, register the image and message data to be displayed using the exclusive application software. Finally, set the program of the schedule function so that the event of MyImage, Messenger and Blank can be executed when the lamp is lighting.
C
Catherine JohnsonSep 7, 2025
What to do if Hitachi CP-WX8650 cannot send an e-mail correctly?
- M
  Mary ScottSep 7, 2025
  If the projector cannot send an e-mail correctly, verify that a test e-mail is sent successfully by pressing the [Send Test Mail] button on the Mail Settings screen of the Projector Web Control. Check the settings on the Mail Settings screen. Ensure a valid e-mail address is set. Confirm that the specific Error/Warning is set to be sent on the Mail Settings screen.