– 19 –
ENGLISH
Ƶ To set SLEEP TIMER and ON TIMER
The air conditioner will be turned off by ECO SLEEP TIMER and turned on by ON TIMER.
1. Set the ON TIMER.
2. Press
(SLEEP) button and set ECO SLEEP TIMER.
Direct the remote controller towards the indoor unit and press
(CANCEL) button.
ƽ “ ”, “ ”, “ ”, “OFF”, off time, “ ”, number of hour, "ON" and ON TIMER set time disappear
from the remote controller display.
ƽ A beep sound emitted from indoor unit and the (TIMER) lamp on the indoor unit turns off.
ƽ
30 minutes after setting ECO SLEEP TIMER, outdoor fan speed will be reduced to lower the noise level and to
1 hour after setting ECO SLEEP TIMER, set temperature will be slightly shifted. Amount of temperature
These automatic operation changes contribute to energy saving without losing comfort.
The level of energy consumption depends on outside temperature, room temperature, set temperature or air
conditioner type.
Cooling operation [diagram representation
for illustrative purpose only]
In this case, air conditioner will turn off in 2 hours (at 1:38) and it will be
turned on at 6:00 the next morning.
NOTE
ƽ
Heating operation [diagram representation for
illustrative purpose only]
Temperature
30 minutes
Outdoor fan
speed reduce
Shift
temperature
1 hour
Temperature
30 minutes
Outdoor fan
speed reduce
Shift
temperature
1 hour
EC O SLEEP TIMER OPERATION
Example:
ECO SLEEP TIMER and ON TIMER reservations are cancelled.
have comfort operation.
shifted depends on type of air conditioner.
Ƶ To cancel EC O SLEEP TIMER and ON TIMER operation
ƽ If ECO SLEEP TIMER is set when OFF TIMER or ON/OFF TIMER has been set earlier, the ECO
SLEEP TIMER becomes effective instead of the OFF TIMER or ON/OFF TIMER.
– 20 –
WEEKLY TIMER OPERATION
Ƶ
Press
(WEEKLY) button. lights up. and blink on the
display. (Mode A is selected).
Press
(WEEKLY) button again, and blink on the display.
(Mode B is selected).
ƽ If no reservation has been made, ON/OFF, , appear.
ƽ If reservation has been made, ON/OFF, , will not
appear.
Press
(WEEKLY) button for about 3 seconds. The selection mode
can be changed.
, day: Mon, program no. : 1, ON/OFF, setting time and setting
temperature blink on the display.
Press
(DAY) button.
The day changes from Mon
Tue Wed Thu Fri Sat Sun
Mon, Tue, Wed, Thu, Fri, Sat, Sun [Full days] Mon, Tue, Wed, Thu,
Fri [weekday]
Sat, Sun [weekend] Mon
Tue ......
Select [Full days] for daily reservation.
Select [weekday] for Monday to Friday reservation.
Select [weekend] for Saturday and Sunday reservation.
ƽAfter reservation has been set, it is easy to check and edit at the same
time.
4. Press
button to select a program number.
The number changes from 1
2 3 4 5 6 1 2 .....
ƽ If program number has been set, follow above in order to make
changes.
1
2
Step 1 : Set the reservation schedule to the remote controller. Send the registered reservation to indoor
unit and then operate.
Step 2 : Select Mode A or Mode B and activate or deactivate WEEKLY TIMER .
Step 3 : Copy and cancel the reservation schedule.
Step 1 : Set reservation schedule to the remote controller. Send the registered reservation
to indoor unit and then operate.
3
4
ƽ If calendar and clock are not set, the reservation setting for WEEKL
ƽ lt is possible to select Mode A or Mode B.For each mode ,up to 6 programs can be set per day. ln total, a
maximum of 42 programs can be set for a week for each mode.
Y TIMER cannot be set.
ƽ If calendar and clock are not set correctly, WEEKLY TIMER will not operate correctly.
ƽ Reservation for calendar and clock shall be set rst before operating WEEKLY TIMER. fi
How to set a WEEKLY TIMER.
1. Select Mode A or Mode B.
2. Set a program.
3. Select the desired day of the wekk.
To Next Page
Loading...
