Hitachi RPC-6.0FSN2E - Timer and Temperature Shift Operations

18
INSTALLATION AND OPERATION MANUAL
5.1.6. TIMER OPERATION PROCEDURE
 Setting current day and time
1. Hold down the SELECT () DAY switch for more than 3 seconds to change to current day setting
mode. SET is indicated and the day blinks. All the days except the current day are indicated.
2. Hold down the SELECT () DAY switch until the current day blinks, then press OK.
The date is indicated, and the time blinks.
3. Press the SELECT () DAY / SCHEDULE switches to adjust the “hour” setting, and then press
again. “Hour” is indicated and “minutes” blinks.
4. Press the SELECT () DAY / SCHEDULE switches to adjust the “minutes” setting, and then press
again. The current time setting mode ends and returns to normal mode. “Minutes” is indicated and the
SET indication goes out. The “seconds” start from zero.
 Setting the timer (programming)
1. Press the TIMER switch. SET and SCHEDULE are indicated. Schedule number “1” blinks and other
numbers are indicated.
2. When the SCHEDULE switch () is pressed, the schedule number moves
[1] → [2] → [3] → [4] → [S] → [1]→….
− Select [S] to set the ON/OFF time and temperature shifts.
− By pressing the TIMER switch, the SET and SCHEDULE indicators go out and the mode changes back
to normal.
3. When the OK switch is pressed, the selected schedule number is indicated. The other schedule number
indicators go out, and the ON time “hour” indicator for the number selected blinks.
4. Press the SELECT () DAY / SCHEDULE switches to adjust the “hour” setting, and then press
again. “Hour” is indicated and “minutes” blinks.
5. Press the SELECT () DAY / SCHEDULE switches to adjust the “minutes” setting, and then press
again. “Minutes” is indicated and the OFF time “hour” setting blinks.
6. Set the OFF time the same way as the ON time. After setting the “minutes”, the OFF time is indicated. If
the schedule number [1][2][3][4] is selected, the indication changes to set the schedule number shown in
2. If [S] is selected, see the section on setting temperature shifts for details.
7. By pressing the () DAY / SCHEDULE switches, the SET and SCHEDULE indicators go out and
the mode returns to normal.
 Dening the schedule to be applied
1. Hold down the () DAY/SCHEDULE switches for more than 3 seconds and the SET indicator
appears. All the days and schedule numbers are indicated.
2. Press the () DAY/SCHEDULE switches until the day you wish to set blinks. When pressed, the
day blinks [Mon] → [Tue] →… → [Sun]→ [Mon~Sun] → [Mon~Fri] → [Sat, Sun] → [Mon]... If several
days are blinking, the same setting will be applied to all the days.
3. Press the () DAY switch until the schedule number you wish to set blinks.
4. Press the () SCHEDULE, and the SCHEDULE indication appears. Then the schedule number
indicated in step 3 is applied to the days set in step 2. Press the OK switch to activate or deactivate the
schedule. If the schedule is activated, the word SCHEDULE is lit up.
5. Press the TIMER switch and the mode returns to normal.
:
SET
Mon Tue
Wed
Thu Fri
Sat
Sun
:
SET
Wed
:
Wed
:
SET
1234S
SCHEDULE
ON

OFF
:
:
SET
1234S
ADDS
SCHEDULE
RNkHR
ON

OFF
:
:
SET
1
SCHEDULE
ON

OFF
:
:
SET
1
SCHEDULE
ON

OFF
:
:
SET
1
SCHEDULE
ON

OFF
:
:
SET
1
SCHEDULE
ON

OFF
:
:
S
NEXT
SCHEDULE
OFF
:
Mon
:
SET
Mon Tue
Wed
Thu Fri
Sat
Sun
:
SET
Mon Tue
Wed
Thu Fri
Sat
Sun
1234S
ON

OFF
:
:
SET
Mon Tue
Wed
Thu Fri
Sat
Sun 1234S
ON

OFF
:
:
SET
Mon Tue
Wed
Thu Fri
Sat
Sun
1234S
SCHEDULE
ON

OFF
:
:
Mon
NEXT
SCHEDULE
OFF
:
PMML0197_r0_04-10.indb 18 08/07/2010 9:20:18