What to do if Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K shows Failure of discharge gas pressure sensor?
If your Hitachi Air Conditioner displays a 'Failure of discharge gas pressure sensor', check the connectors for any looseness or breakage. The issue may be a loose, disconnected, broken, or short-circuited connector.
What to do if Hitachi Air Conditioner shows abnormal transmission between outdoor and indoor units?
If your Hitachi Air Conditioner shows 'Abnormal transmission between outdoor and indoor units', check the wiring, terminals, and PCB for faults. This issue can be caused by incorrect wiring, loose terminals, PCB failure, a tripped fuse, or the power supply being OFF.
Why does my Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K Air Conditioner activate safety device from excessively high discharge pressure?
If your Hitachi Air Conditioner activates the safety device due to excessively high discharge pressure, inspect the heat exchanger and refrigerant conditions. This activation can be caused by overload (obstruction of HEX, short circuit), a mixture of inert gas, or excessive refrigerant.
What causes Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K to activate safety device from excessively low suction pressure?
If your Hitachi Air Conditioner activates the safety device from excessively low suction pressure, inspect refrigerant levels and piping for blockages. This issue is often due to a shortage or leakage of refrigerant, piping clogging, a closed expansion valve, or a locked fan motor.
What causes Abnormality of picking up circuit for protection (Outdoor unit) in Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K Air Conditioner?
If your Hitachi Air Conditioner displays 'Abnormality of picking up circuit for protection (Outdoor unit)', inspect indoor unit PCB and wiring. The cause can be a failure of indoor unit PCB, incorrect wiring, or connection to PCB in the indoor unit.
What to do if Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K shows Transmission error between Inverter PCB and Main PCB?
Inspect connection between Inverter PCB and Main PCB.
What does Decrease in discharge gas superheat mean for Hitachi Air Conditioner?
If your Hitachi Air Conditioner displays 'Decrease in discharge gas superheat', check refrigerant charge and inspect related components. Possible causes are excessive refrigerant charge, failure of thermistor, incorrect wiring, incorrect piping connection, or expansion valve locking at opened position (disconnected connector).
How to solve RF Communication failure on Hitachi Air Conditioner?
If your Hitachi Air Conditioner shows 'RF Communication failure', check the RF communication setup. This issue occurs when there is no communication for 1 hour with one or two RF receivers which are bound to the RF-Bridge.
What causes Hitachi Air Conditioner hydraulic alarm pressure?
If your Hitachi Air Conditioner displays 'Hydraulic alarm pressure', check the system for any leaks or blockages affecting water pressure. This alarm indicates that water pressure is not detected in the hydraulic cycle.
How to fix Incorrect PCB Setting in Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K?
If your Hitachi Air Conditioner shows 'Incorrect PCB Setting', correct the DSW settings. This issue is caused by a wrong DSW setting in the case of Co041.
General| Heating Capacity | 3.0 kW |
|---|---|
| Refrigerant | R32 |
| Energy Efficiency Ratio (Heating) | 4.5 |
| Weight (Indoor Unit) | 45 kg |
| Type | Air to Water Heat Pump |
| Power Supply | 220-240 V, 50 Hz |
Provides crucial safety warnings and precautions for handling and operating the heat pump.
Highlights critical instructions for installation, use, and operation to prevent faults or damage.
Defines the operational temperature limits for space heating, DHW, and pool heating.
Covers refrigerant piping length, size, and installation guidelines.
Outlines safety measures and concentration limits for refrigerant leaks.
Details wiring sizes and minimum requirements for protection devices.
Guides the user through the initial setup and configuration of the controller.
Details procedures for air purging, unit testing, and screed drying.
Lists and explains alarm codes and their main causes for indoor units.
Lists and explains alarm codes and their main causes for outdoor units.
Detailed maintenance steps for the outdoor unit's components.
Detailed maintenance steps for the indoor unit's components and piping.
To Next Page