To Next Page
A
Amanda MontesAug 31, 2025
What to do if Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K has Receiver Communication failure?
- WwsmithAug 31, 2025
If your Hitachi Air Conditioner is not receiving a signal, check the Opentherm/Hlink connection.
What to do if Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K has Receiver Communication failure?
If your Hitachi Air Conditioner is not receiving a signal, check the Opentherm/Hlink connection.
How to fix Incorrect PCB Setting in Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K?
If your Hitachi Air Conditioner shows 'Incorrect PCB Setting', correct the DSW settings. This issue is caused by a wrong DSW setting in the case of Co041.
How to correct Hitachi Air Conditioner incorrect indoor unit number setting?
If your Hitachi Air Conditioner displays 'Incorrect indoor unit number setting', correct the indoor unit number settings. This issue can be caused by duplication of indoor unit numbers or the number of indoor units exceeding specifications.
How do I fix a 'Unit Capacity setting Error' on my Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K?
If your Hitachi Air Conditioner displays a 'Unit Capacity setting Error', ensure correct capacity settings for both indoor and outdoor units. This error indicates a mismatch between the indoor and outdoor unit capacities.
How to fix Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K activation of overcurrent protection?
If your Hitachi Air Conditioner activates overcurrent protection, inspect the inverter PCB and compressor operation. This can be caused by overload, overcurrent, failure of the Inverter PCB, a clogged heat exchanger, a locked compressor, or EVI/EVO failure.
What to do if Hitachi Air Conditioner shows Thermostat Heater Alarm?
If your Hitachi Air Conditioner is showing a high temperature in the electric heater, check the electric heater for proper operation.
How to troubleshoot Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K Air Conditioner hydraulic alarm flow and water pump malfunction?
If your Hitachi Air Conditioner displays a hydraulic alarm related to flow and water pump malfunction, check the water pump for proper operation and repair or replace it if defective. This alarm indicates that water flow is not detected in the hydraulic cycle or the pump is defective.
What causes Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K to activate safety device from excessively low suction pressure?
If your Hitachi Air Conditioner activates the safety device from excessively low suction pressure, inspect refrigerant levels and piping for blockages. This issue is often due to a shortage or leakage of refrigerant, piping clogging, a closed expansion valve, or a locked fan motor.
Why does my Hitachi YUTAKI S COMBI RWD-3.0NWE-200S-K Air Conditioner activate safety device from excessively high discharge pressure?
If your Hitachi Air Conditioner activates the safety device due to excessively high discharge pressure, inspect the heat exchanger and refrigerant conditions. This activation can be caused by overload (obstruction of HEX, short circuit), a mixture of inert gas, or excessive refrigerant.
What to do if Hitachi Air Conditioner shows abnormal transmission between outdoor and indoor units?
If your Hitachi Air Conditioner shows 'Abnormal transmission between outdoor and indoor units', check the wiring, terminals, and PCB for faults. This issue can be caused by incorrect wiring, loose terminals, PCB failure, a tripped fuse, or the power supply being OFF.
General| Heating Capacity | 3.0 kW |
|---|---|
| Refrigerant | R32 |
| Energy Efficiency Ratio (Heating) | 4.5 |
| Weight (Indoor Unit) | 45 kg |
| Type | Air to Water Heat Pump |
| Power Supply | 220-240 V, 50 Hz |
Provides crucial safety warnings and precautions for handling and operating the heat pump.
Highlights critical instructions for installation, use, and operation to prevent faults or damage.
Defines the operational temperature limits for space heating, DHW, and pool heating.
Covers refrigerant piping length, size, and installation guidelines.
Outlines safety measures and concentration limits for refrigerant leaks.
Details wiring sizes and minimum requirements for protection devices.
Guides the user through the initial setup and configuration of the controller.
Details procedures for air purging, unit testing, and screed drying.
Lists and explains alarm codes and their main causes for indoor units.
Lists and explains alarm codes and their main causes for outdoor units.
Detailed maintenance steps for the outdoor unit's components.
Detailed maintenance steps for the indoor unit's components and piping.
