To Next PageTo Next PageWhat to do if coolant temperature is too high in Hitachi Excavators?
If the coolant temperature in your Hitachi Excavators is too high, it could be due to: * Low coolant level: Refill the coolant. * Insufficient fan belt tension: Adjust the fan belt tension. * Damaged rubber hose: Replace the damaged hose. * Faulty thermostat: Replace the thermostat. * Faulty coolant temperature gauge: Replace the gauge.
What causes Hitachi Excavators batteries to discharge quickly?
If the batteries in your Hitachi Excavators discharge quickly after being charged, it could be due to: * A shorted cable: Repair or replace the cable. * A shorted battery separator: Repair or replace the separator. * Increased sediment in the battery: Replace the battery.
What to do if Hitachi Excavators starter rotates but doesn't start?
If the starter rotates but the Hitachi Excavators engine doesn't start, check for: * No fuel: Ensure there are no fuel leaks and refill the fuel. * Air in the fuel system: Bleed the air from the system. * Clogged fuel filter: Drain any water and replace the filter element. * Frozen fuel: Warm the fuel pump with hot water or wait for the temperature to rise.
Why do Hitachi ZAXIS 225USLC-5B batteries will not be charged?
If the batteries in your Hitachi Excavators are not charging, it could be due to: * A broken battery separator: Replace the separator. * A faulty regulator: Adjust and replace the regulator. * A faulty ground line: Repair the ground line. * A faulty alternator: Repair or replace the alternator.
What to do if Hitachi Excavators engine stalls soon after starting?
If your Hitachi Excavators engine stalls soon after starting, consider the following: * Too low idle speed: Repair the idle speed. * Clogged fuel filter: Drain water and replace the element. * Clogged pre-fuel filter: Clean or replace the element. * Faulty engine control system: Repair the engine control system. * Clogged air cleaner: Clean or replace the element. * Faulty injection pump: Repair the injection pump.
Why is my Hitachi ZAXIS 225USLC-5B engine running irregularly?
An Hitachi Excavators engine running irregularly may be caused by: * A faulty fuel system: Repair the fuel system. * Water or air in the fuel system: Drain water or bleed air. * A faulty engine control system: Repair the engine control system. * A clogged muffler filter: Repair the muffler filter.
Why is the lever heavy to operate on Hitachi ZAXIS 225USLC-5B Excavators?
If the lever is heavy to operate on your Hitachi Excavators, it could be due to: * A rusted joint: Lubricate or repair the joint. * A worn pusher: Replace the pusher.
Why is the swing not smooth on Hitachi Excavators?
If the swing function on your Hitachi Excavators is not smooth, it could be due to: * A worn swing gear: Repair or replace the swing gear. * Damaged swing bearing and bearing balls: Repair or replace the swing bearing and bearing balls. * Lack of grease: Refill grease.
Why does the hydraulic oil temperature increase in Hitachi ZAXIS 225USLC-5B?
If the hydraulic oil temperature increases in your Hitachi Excavators, it could be due to: * Stained oil cooler: Clean the oil cooler. * Insufficient engine fan belt tension: Adjust the engine fan belt tension.
What causes Hitachi Excavators to not travel smoothly?
If your Hitachi Excavators does not travel smoothly, it could be due to: * Overly tensioned or slackened crawler sag: Adjust the crawler sag. * Lack of lubricant in front idler and/or roller: Refill lubricant. * Deformed track frame: Repair or replace the track frame. * Embedded foreign matter such as rock fragments: Remove the foreign matter. * Dragged parking brake: Repair the parking brake.
General| Brand | Hitachi |
|---|---|
| Model | ZAXIS 225USLC-5B |
| Category | Excavators |
| Language | English |
Covers recognizing safety symbols, understanding signal words, following instructions, preparing for emergencies, wearing protective clothing, and general cab precautions.
Details safe operating procedures, including moving the machine, operating from the seat, avoiding common accidents, and keeping the work area clear.
Details the ISO pattern control levers for machine functions and the operation of attachment pedals for breakers and crushers.
Outlines correct service procedures, daily checks, and preparations for inspection and maintenance.
Covers checking and changing engine oil, fuel filters, hydraulic oil, air cleaner elements, and coolant.
