User Manual of Water-Proof Brushless Speed Controller (RTR Version) HW-SM601ENG-20140903 Page - 1 -
USER MANUAL
WATER-PROOF
SENSORLESS BRUSHLESS
SPEED CONTROLLER
( RTR VERSION )
【DECLARATION】
Thanks for purchasing our electronic speed controller (ESC). The power system for RC model can be very
dangerous, so please read this manual carefully. In that we have no control over the correct use,
installation, application, or maintenance of our products, no liability shall be assumed nor accepted for
any damages, losses or costs resulting from the use of the product.
【FEATURES】
1. Water-proof and dust-proof. The ESC can work under water for a short time.
(Please remove the cooling fan when running car in water, and after running, please make the ESC
clean and then dry it to avoid the oxidation to copper connectors)
2. Specially designed for RC car and truck, with excellent start-up, acceleration and linearity features.
3. Drive sensorless brushless motors.
4. 2 running modes (“Forward with brake” mode, “Forward/Backward with brake” mode).
5. Proportional ABS brake function with 4 steps of maximum brake force adjustment, 8 steps of drag-brake force
adjustment.
6. 4 start modes (“Punch”) from “Soft” to “Very aggressive” to be suitable for different chassis, tires and tracks.
7. Multiple protection features: Low voltage cut-off protection for Lipo or NiMH battery / Over-heat protection /
Throttle signal loss protection / Motor blocked protection.
8. Easily programmed with the “SET” button on the ESC or with the LED Program Card.
【SPECIFICATIONS】
WP-S16-RTR WP-10BL50-RTR WP-S10E-RTR
0.005 ohm
0.0010 ohm 0.0012 ohm
36*28*21 / 38g 48.5*38*32 / 90g 48.5*38*32 /90g
WP-S10D-RTR
WP-S10DS-RTR
WP-10BL60-RTR
1/10 scale on-road and off-road
On-road: ≥9T
Off-road: ≥12T
3650 size motor
On-road: ≥5.5T
Off-road: ≥9T
3650 size motor
On-road: ≥9T
Off-road: ≥12T
3650 size motor
4-9 cells NiMH or 2-3S Lipo
Rating Voltage of
the Stock Cooling
Fan (*Note 1)
On-road: ≥12T
Off-road: ≥18T
2040 size motor
On-road: ≥18T
Off-road: ≥24T
2040 size motor
On-road: ≥12T
Off-road: ≥18T
3650 size motor
WP-S10D-RTR: 5V*
WP-S10DS-RTR: 5V*
WP-10BL60-RTR:7.4V
On-road: ≥8T
Off-road: ≥11T
3650 size motor
On-road: ≥11T
Off-road: ≥14T
3650 size motor
* The stock 5V cooling fan only works with 2S Lipo or 4-6 cells NiMH.
When using 3S Lipo or 7-9 cells NiMH, the stock 5V cooling fan MUST
be replaced by 7.4V or 12V cololing fan.
Multiplexed with cooling fan port
On-road: ≥12T
Off-road: ≥18T
3650 size motor
On-road: ≥8.5T
Off-road: ≥13T
3650 size motor
WP-S10D-RTR:
49*34*35 / 75g
WP-S10DS-RTR:
49*32*41 / 75g
WP-10BL60-RTR:
48.5*38*32 / 90g
* Note1: Please remove the cooling fan when running the ESC in water. For more information about the 12V
cooling fan, please refer to the brief
introduction on page 3.
【BEGIN TO USE THE NEW ESC】
1. Connect the ESC, motor, receiver,
battery and servo according to the
following diagram
“+” and “-” wires of the ESC are
connected with the battery pack, and #A,
#B and #C are connected with the motor
wires. The “SET” button is used for
programming the ESC.
The control cable of the ESC (trio wires
with black, red and white color) is
connected with the throttle channel of the
receiver (Usually CH2).
1The #A, #B, #C wires of the ESC can be
connected with the motor wires freely
(without any order). If the motor runs in