SPECIFICATIONS
Power: ....................................................................................................... 3V lithium battery (Duracell DL123A, Panasonic CR123A)
CAUTION: Risk of fire, explosion, and burns. Do not recharge, disassemble, heat above 212°F (100°C) or incinerate. Dispose of used batteries
properly. Keep away from children.
Operating Temperature: ...................................................................................................................... 14°F (-10°C) to 104°F (+40°C)
Operating Voltage: 3.2VDC
Dimensions: ......................................................................................................................................3.1” length, 1.6”wide, 1.0” depth
Sensor Parameters:
Cold Temperature (Freeze) Detector: .................................................................................................................................. 45°F (7°C)
Warm Temperature Detector: ............................................................................................................................................. 75°F (24°C)
Hot Temperature Detector: ................................................................................................................................................. 95°F (35°C)
Refrigerator Failure Detector: ............................................................................................................................................... 42°F (6°C)
Freezer Failure Detector:................................................................................................................................................... 10°F (-12°C)
Hysteresis
***: ...................................................................................................................................................................................... 3°F (-16°C)
Flood Sensor: ................................................................................................................................ ¼ inch of water covering the probe
Response Time Tolerance
****: ......................................................................................................................................................... +50%, -20%
Temperature Measurement Accuracy (internal temp. sensor or external temp. probe): ................................................... ±3°F (-16°C)
*** Hysteresis is the temperature difference between “fault” and “restore” points.
**** The Response Time Tolerance is the time duration necessary for the device to respond to a “fault” or “restore” condition. This time does not take
into account the time necessary for the probe and circuitry to equalize to the ambient temperature. This feature prevents false alarms due to
open doors and other transitory conditions.
TO THE INSTALLER
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The
installer should assume the responsibility of developing and offering a regular maintenance program to the user, as well as acquainting the user with the proper operation and
limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to insure the system’s
operation at all times.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS: The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC/IC NOTICE: This device complies with Part 15 of the FCC Rules, and RSS-210 of IC. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet
appareil ne doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE
ENTIRE ALARM SYSTEM.
Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-577-2000
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited.
SUPPORT & WARRANTY INFORMATION
For the latest documentation and support, please go to: www.resideo.com
For the latest warranty information, please go to: www.security.honeywellhome.com/warranty
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product manufactured by Resideo Technologies, Inc. and its affiliates
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2020 Resideo Technologies, Inc.
www.resideo.com
ÊK9947V4DvŠ
K9947V4D 9/15 Rev. D
To Previous Page
Loading...
Need help?
General
