Honeywell ADEMCO VISTA SERIES User Manual (English)

Other manuals for Honeywell ADEMCO VISTA SERIES

Installation And Setup Guide40 pages

Programming Guide48 pages

Faq4 pages

Questions and Answers:

J
Justin MurphySep 8, 2025
What to do if my Honeywell ADEMCO VISTA wireless zone is in 'Check'?
- R
  ryanadamsSep 8, 2025
  If a wireless zone on your Honeywell Security System is in 'Check', it could be due to a 'trouble' Zone Type, a tamper, or a missing check-in signal. If it's a missing check-in (indicated by E381), relocate the transmitter and/or receiver, or add a 5800RP to extend the range. If it's a tamper condition (E383), restore the cover or wall tamper of the transmitter and disarm the keypad twice.
M
Michael JonesSep 7, 2025
What causes Honeywell ADEMCO VISTA Security System zone doubled zones to be in 'Check'?
- T
  thomas93Sep 7, 2025
  If zone doubled zones are in 'Check' on your Honeywell Security System, it indicates a short on one of the zone circuits; if one is shorted, both are shorted. Check the wiring. Also, use only Normally Closed contacts for doubled zones. A Normally Open device will short both zones when activated.
J
Jessica HarperSep 6, 2025
What does 'Check 103 XXXX' mean on my Honeywell Security System?
- R
  Richard FloresSep 6, 2025
  To diagnose a 'Check 103 XXXX' error on your Honeywell Security System, connect an alpha keypad. This will display 'Check 103' along with a 4-digit code, which will help identify the specific problem with the communicator.
K
Kelly CrawfordSep 5, 2025
Why is my Honeywell ADEMCO VISTA Security System wireless not working, working intermittently, or delayed response?
- D
  Debbie LaneSep 5, 2025
  If your Honeywell Security System's wireless functionality is inconsistent, it might be due to having two receivers connected to the system. Watch the red LED on the receiver to see if it flashes when a transmitter is triggered.
D
Donna JohnsonAug 23, 2025
Why is my Honeywell ADEMCO VISTA keypad blank?
- J
  Jeffery SampsonAug 23, 2025
  A blank keypad on your Honeywell Security System may be due to several reasons. First, verify the power and connections to the keypad, ensuring a voltage of 12-13Vdc. Also, check the keypad address, which should be between 16-23, and if it's 17-23, confirm it's enabled in programming fields *190-*196. If the keypad uses a separate power supply, establish a common ground wire between the power supply negative and the panel's auxiliary power negative, located at terminal 4.
K
Kurt WilsonSep 3, 2025
What does 'Check 107 – 111' mean on my Honeywell ADEMCO VISTA?
- B
  Brandy MckeeSep 3, 2025
  The 'Check 1XX' error (where XX represents the 4219/4229 address) on your Honeywell Security System indicates a potential issue with the expander. If the zones are functioning despite the error, the cover tamper may not be engaged. If the zones are also in a 'Check' state, the expander has likely lost ECP communication with the panel. If there are no expanders on the system and no zones are enabled, check all 16 outputs in *79 and delete any that are enabled for the address in trouble.
D
deborahharrisonSep 2, 2025
Why does my Honeywell Security System panel revert to Stay mode after arming Away?
- E
  elliottfaithSep 3, 2025
  If your Honeywell Security System panel reverts to Stay mode after arming Away, the Auto Stay feature is likely enabled in *84 by default.
J
Johnny HernandezSep 2, 2025
What does 'Telco Fault' mean on my Honeywell ADEMCO VISTA?
- L
  Leonard PerrySep 2, 2025
  The 'Telco Fault' message on your Honeywell Security System, along with 'Check 94', indicates that the Telephone Line Fault Monitor is enabled in *92, but the panel isn't detecting at least 3Vdc on the phone line.
C
Courtney JonesSep 1, 2025
What does the 'Check 100' error mean for my Honeywell ADEMCO VISTA Security System wireless receiver?
- J
  Jessica JuarezSep 1, 2025
  The 'Check 100' error on your Honeywell Security System indicates a problem with the wireless receiver. This can be caused by a jam condition if the 'RF Jam' option is not enabled in *22. Verify that only one receiver is connected to the panel. If the receiver has lost ECP communication, check that the dip switches are correctly configured. If there is no receiver, remove any zone with a serial number or enter all 0’s in the *24 House ID location in programming.
R
Renee GonzalezAug 31, 2025
Why is my Honeywell Security System keypad not providing exit beeps when arming Away or Max?
- F
  Frank WilsonAug 31, 2025
  If your Honeywell Security System keypad isn't providing exit beeps when arming in Away or Max mode, ensure that *37 'Audible Exit Warning' is enabled for exit beeps on all keypads. Also, keypad sounds may be suppressed in the second digit of the keypad addressing fields *190 - *196. This can suppress Chime, Entry/Exit, and Arm/Disarm beeps from specific keypads.

Honeywell ADEMCO VISTA SERIES Specifications

General

Zones	Up to 48 zones
Keypads	Supports multiple keypads
Communication	Phone line, cellular, or internet
Remote Access	Yes
System Type	Wired/Wireless Hybrid
Power Supply	16.5VAC
Backup Battery	Rechargeable lead-acid