EasyManua.ls Logo

Honeywell HL10 Series - User Manual

Honeywell HL10 Series
14 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model / Modèle / Modelo:
o
C
o
F
COOL
DRY
FAN
POWER
TIMER
SLEEP
WATER
FULL
HIGH
MID
LOW
TIMER
SLEEP
HL10 Series / Série / Serie: HL10CESWW, HL10CESWK, HL10CESWG, HL10CESWB
HL12 Series / Série / Serie: HL12CESWW, HL12CESWK, HL12CESWG, HL12CESWB
HL14 Series / Série / Serie: HL14CESWW, HL14CESWK, HL14CESWG, HL14CESWB
HL14CHESWW, HL14CHESWK, HL14CHESWG, HL14CHESWB
Portable Air Conditioner
User Manual
Email: usinfo@jmatek.com
Web: www.jmatek.com

Table of Contents

Questions and Answers

  • R
    Robert ScottAug 13, 2025
    Why is my Honeywell HL10 running but not cooling?
    • A
      anthony71Aug 13, 2025
      Several factors can cause your Honeywell Air Conditioner to run without cooling effectively. Check if any doors or windows are open and close them. Ensure the air filter is clean. Verify that the exhaust hose is properly reinstalled. Reduce the temperature setting. Remove any blockages from the air outlet or intake. If the room is too large, move the unit to a smaller room. Covering windows with curtains or blinds can also improve cooling effectiveness.
  • K
    Kelly MartinAug 17, 2025
    How to fix a Honeywell HL10 Air Conditioner that does not start?
    • L
      Laura GutierrezAug 17, 2025
      If your Honeywell Air Conditioner doesn't start, begin by checking if there is electricity. Replace the remote control batteries. Ensure the power cord is properly plugged in by removing and reconnecting it. If you are in the USA, Canada, or Mexico, reset the safety LCDI plug.
  • J
    Joshua ScottAug 20, 2025
    Why does my Honeywell Air Conditioner only run for a short while?
    • C
      Carrie MartinezAug 20, 2025
      Your Honeywell Air Conditioner might run only briefly due to a few reasons. First, the thermostat temperature setting might be too close to the room temperature; try lowering the set temperature. Second, the air outlet could be blocked, so ensure the exhaust hose is properly connected. Finally, tight bends in the air exhaust hose can cause this issue; connect the exhaust hose as per instructions.
  • J
    Jeffrey RamirezAug 25, 2025
    Why is the heater not switching on in my Honeywell HL10?
    • A
      andreacruzAug 25, 2025
      The heater might not switch on in your Honeywell Air Conditioner if the heating function hasn't been activated. The Heating* function should be activated when the ambient temperature reaches below 25°C (77°F). Also, ensure the temperature setting is not too high, as Heating* is only activated when the ambient temperature is below 25°C (77°F).
  • R
    Randall BrownAug 28, 2025
    What to do if my Honeywell HL10 Air Conditioner does not start?
    • R
      Rachel LopezAug 28, 2025
      If your Honeywell Air Conditioner isn't starting, begin by checking for power. Replace the remote control batteries. If that doesn't work, remove and reconnect the power cord. If the issue persists, reset the safety LCDI plug. If problems continue, contact customer support (USA / Canada / Mexico only).
  • Z
    zacharycolemanSep 1, 2025
    What to do if the power button is blinking on my Honeywell Air Conditioner?
    • P
      pearsonamySep 1, 2025
      If the power button on your Honeywell Air Conditioner is blinking, and it indicates a water full condition, it means there's likely excess water condensation inside the tank. You should drain the water, following the instructions for Water Condensation Drainage.
  • D
    Dawn FergusonSep 5, 2025
    What to do if my Honeywell Air Conditioner runs only a short while?
    • D
      diazerikSep 5, 2025
      If your Honeywell Air Conditioner runs only for a short time, it might be due to thermostat settings. Try lowering the set temperature, as it may be too close to the room temperature. Also, ensure that the air outlet isn't blocked and that the exhaust hose is properly connected.
  • A
    amyroySep 8, 2025
    Why is the power button blinking on my Honeywell Air Conditioner?
    • D
      Diana FlowersSep 8, 2025
      If the power button indicator is blinking on your Honeywell Air Conditioner, it usually means there is excess water condensation inside the tank. You will need to drain the water.

Summary

General Safety Guidelines

Usage Tips and Best Practices

Product Parts Overview

Installation and Setup

Installation Steps

Step-by-step guide for setting up the portable air conditioner.

Operating Your Air Conditioner

Control Panel Functions

Overview and functions of the unit's control panel.

Key Operational Buttons

Functional Buttons Explained

Detailed explanation of the unit's operational buttons and modes.

Fan Speed and Timer Management

Fan Speed and Timer Settings

Adjusting fan speed, setting auto turn-off and turn-on timers.

Remote Control Operation

Remote Battery and Safety Notes

Instructions for inserting batteries and safety precautions for remote control use.

Cleaning and Maintenance Schedule

Unit and Air Filter Cleaning

Procedures for cleaning the unit and its air filters.

End-of-Season Storage Guide

Steps for preparing the unit for long-term storage.

Water Condensation Management

Manual Drainage Procedure

Procedure for manually draining excess water condensation from the unit.

Continuous Drainage Method

Method for continuous drainage, especially in dehumidifier mode.

Troubleshooting Common Problems

Honeywell HL10 Series Specifications

General IconGeneral
Cooling Capacity10, 000 BTU
Power Supply115 V / 60 Hz
RefrigerantR410A
Control TypeElectronic
Filter TypeWashable
Power Consumption (Cooling)1150 W
TypePortable
AreaUp to 450 sq ft
Fan Speed3 speeds
Noise Level (High)52 dB
Timer24-hour

Related product manuals