Honeywell PRO 2000 Series Product Information

PRO
2000 Series
Programmable
Digital
Thermostat
Product
Information
33-00304EFS-01
Quick reference to controls
Product Manuals
Search online for Honeywell 69-2608EFS for the Owner’s Guide.
Set the time and day
Select the system setting
Select the fan setting
Quick reference to display screen
Energy saving settings for maximum cost
savings
CAUTION
Equipment damage hazard
To prevent possible compressor damage, do not
operate cooling system when outdoor temperature is
below 50°F (10°C).
To adjust program schedules
M32781
E.M. Heat Heat Off Cool Auto On
Fan
Temperature
adjustment
Screen Lit for 12 seconds when you press any button.
Set: Press to set time/
day/schedule.
Hold: Press to
override programmed
temperature control.
Run: Press to resume
program schedule.
M32701
We
Lo
Batt
Wake
Set
am
Heat
75
On
6
:
30
Low battery warning
Setpoint indicator
Appears when the
setpoint temperature is
displayed.
Temperature
The ambient
(measured)
temperature is
normally displayed.
To view the setpoint
temperature,
press the Up or
Down button
once. The setpoint
temperature will
System status
Cool On: Cooling system is on.
Heat On: Heating system is on.
Aux On: Auxiliary heat is on.
(Only for heat pumps with this capability [select models only].)
When Heat On or Cool On is flashing, compressor protection is engaged.
Current day/time
Current program period
Wake/Leave/
Return/Sleep
appear for five seconds.
Set Time
am
6
:
30
M32702
Set Day
We
M32703
1. Press the SET button, then press s or
t to set the clock time.
2. Press the SET button, then press s or
t to select the day of the week.
3. Press RUN to save & exit.
Note: If the clock flashes, the thermostat
will follow your settings for the Monday
“Wake” time period until you reset the time
and day.
Press SET, then adjust time.
Press SET, then select current day.
M32781
E.M. Heat Heat Off Cool Auto On
Fan
The SYSTEM switch can be set to control
your heating or cooling system, depending
on the season.
• Cool: Cooling system control.
• Off: All systems are off.
• Heat: Heating system control.
• Em Heat: Emergency & Auxiliary
Heat control. Compressor is locked
out. (Select models only.)
Set SYSTEM switch to control the
heating or cooling system.
Set the FAN switch to Auto or On.
In “Auto” mode (the most commonly
used setting), the fan runs only when the
heating or cooling system is on.
If set to “On,” the fan runs continuously.
Set FAN switch to choose whether the fan
runs continuously or only as needed.
This thermostat is pre-set to use energy saving program settings. We recommend
these settings, since they can reduce your heating/cooling expenses. (See next page
to adjust times and temperatures of each time period.)
M32781
E.M. Heat Heat Off Cool Auto On
Fan
Wake
(6:00 am)
Leave
(8:00 am)
Return
(6:00 pm)
Sleep
(10:00 pm)
Cool
(MonFri)
Heat
(MonFri)
Heat
(SatSun)
Cool
(SatSun)
70
°
78
°
70
°
78
°
62
°
85
°
62
°
85
°
70
°
78
°
70
°
78
°
62
°
82
°
62
°
82
°
Mo Tu We Th Fr
Wake
Set Schedule
Set
am
75
6
:
30
M32706
1. Press SET until Set Schedule is
displayed.
2. Press s or t to set your weekday
Wake time (MoFr), then press SET.
3. Press s or t to set the
temperature for this time period,
then press SET.
4. Set time and temperature for the
next time period (Leave). Repeat
steps 2 and 3 for each weekday
time period.
Press SET 3 times,
then adjust time.
Press SET, then set
desired temperature.
5. Press SET to set weekend time periods (Sa & Su), then press RUN to save & exit.
Note: Make sure the thermostat is set to the system you want to program (Heat or
Cool).

Honeywell PRO 2000 Series Specifications

General

Display Type	Digital
Programmable	Yes
Stages	1 Heat/1 Cool
Temperature Control	±1°F
Hold Feature	Yes
Filter Change Alert	Yes
Low Battery Indicator	Yes
Power Source	Battery or Hardwired
Temperature Range	40°F to 90°F (4°C to 32°C)