11
Overlap strokes by ½ inch to help prevent
streaking.
12
It is best to alternate wet and dry strokes as
described in steps.
To avoid saturating carpet, do not
use more than 4 wet strokes over
any one area. Always end with dry
strokes.
If additional cleaning is necessary,
wait until the carpet is completely
dry before using the tool again.
TIP
TROUBLESHOOTING
THIS PRODUCT CONTAINS NO SERVICEABLE PARTS.
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-944-9200 PRIOR TO CONTINUING USE.
ALWAYS IDENTIFY YOUR CLEANER BY THE COMPLETE MODEL NUMBER. (THE MODEL NUMBER APPEARS ON THE BACK OF THE CLEANER.)
WARNING:
To reduce the risk of personal injury, unplug before cleaning or
servicing.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
Cleaner won’t run
1. Plug unit in firmly.
2. No voltage in wall plug
2. Check fuse or breaker in home.
3. Blown fuse or tripped breaker
3. Replace fuse or reset breaker in home.
4. Call Customer Service at 1-800-944 -9200 prior to continuing use.
5. On⁄Off pedal not depressed
5. Press pedal.
Low suction 1. Dirty Water Tank full⁄automatic shut off engaged 1. Remove and empty Dirty Water Tank. See "How to Empty Dirty Water."
2. Blockage in tool on end of hose 2. Remove tool and clear blockage.
3. Dirty Water Lid not on correctly 3. Make sure lid is on securely. See "How to Empty Dirty Water."
4. Dirty Water Tank Debris Filter clogged 4. See "How to Clean Carpets."
5. Blockage in Nozzle 5. See "How to Clean Carpets."
6. Dirty Water Tank not properly secured 6. Replace Dirty Water Tank and secure Dirty Water Tank latch.
7. Dirty Water Nozzle not on correctly 7. Remove and replace Dirty Water Nozzle. See "How to Remove & Clean Nozzle"
8. Blockage in hose 8. Drop a coin through, clear with broom handle.
Hose Nozzle stops spraying liquid during
use
1. Clean Water Tank or Detergent Container is empty 1. Turn off Cleaner and fill Clean Water Tank & Detergent Container.
2. Loose connection to solution port on foot of cleaner 2. Check for secure connection to solution port on body of Cleaner.
Accessory Tool will not spray after filling
the Clean Water Tank or Solution Tank
1. Air is trapped in the hose & pump 1. Turn on the Cleaner. If hose dœs not spray, prime the pump by lowering the hose
down to the floor and hold the trigger for up to one minute.
2. Aim downward & squeeze trigger.
Hose will not spray after priming pump 1. Pump is defective 1. Call for service: 1-800-944-9200.
2. Not connected properly 2. Check connection.
Clean water won’t dispense 1. Clean Water Tank or Solution Tank not firmly in place 1. Make sure tank is securely locked in position.
2. Clean Water Tank or Solution Tank empty 2. Refill container according to cleaning instructions.
Solution won’t dispense 1. Cleaner is not moving in forward direction 1. Must be moving the machine forward to properly dispense water and solution.
Brushes won’t rotate during floor cleaning 1. Brushroll stall protection activated 1. Turn the unit off and back on, then inspect and clean for jams.
2. Unit in upright position 2. Brushes will not rotate in upright position. Step on handle release to start cleaning.
Water is leaking out of Carpet Cleaner 1. Clean Water Tank, Solution Tank or Dirty Water Tank not FIRMLY in place. 1. Make sure the tank is secure.
2. Carpet Cleaner may drip residual moisture after use. Allow cleaner and brushes to
dry before storing on hard floor surface.
To Next Page
Loading...
