horiba HP-200 User Manual (English)

Other manuals for horiba HP-200

Questions and Answers:

D
Diana WoodAug 21, 2025
What to do if I see fluctuation in measured value with horiba HP-200 Measuring Instruments?
- M
  Mike CollinsAug 21, 2025
  If you observe fluctuations in the measured value, several factors could be responsible: * Air bubbles may be adhering to the electrode. Ensure no air bubbles are generated in the solution. * A fast flow rate might be creating air bubbles. Try controlling the flow rate. * Fluctuations in the solution level can change the wetted area of the electrode. Install the HP-200 to prevent solution level fluctuations. * A sudden change in solution temperature can cause fluctuations. Install the HP-200 in a location with stable temperatures. * A loose screw on the terminal block can cause fluctuations. Firmly tighten the screw. * Moisture on the terminal block can cause fluctuations. Remove any moisture. * A dirty terminal block can cause fluctuations. Clean the terminal block.
R
Roy MorganAug 22, 2025
Why is my horiba HP-200 Measuring Instruments showing an abnormal reading?
- B
  Billy VillegasAug 23, 2025
  An abnormal reading may occur for several reasons: * The electrode might be dirty. Clean the electrode. * The electrode may not be fully immersed in the solution. Install the HP-200 to ensure the electrode is always immersed. * The electrode cable could be broken or short-circuited. Inspect the electrode cable. * There may be a contact failure on the terminal block. Check the terminal block.
E
eatonbruceAug 25, 2025
What to do if Horiba Measuring Instruments displays blinking (out of measurable range)?
- K
  kendra72Aug 25, 2025
  A blinking display, indicating that the measurement is out of range, can occur for these reasons: * The electrode is not immersed in the solution. Install the HP-200 so that the electrode remains immersed even if the solution level fluctuates. * The protective cap is still on the electrode. Remove the protective cap. * The electrode cable is improperly wired, particularly with electrical discontinuity in the G- or R-line. Check for loosened screws on the terminal blocks in the HP-200 and the relay box, and verify the wiring.
K
Krista HartAug 26, 2025
What to do if my horiba HP-200 show slow response?
- G
  Gary FreemanAug 27, 2025
  A slow response could be due to: * A low flow rate. Increase the flow rate. * Uneven concentrations in the solution, especially in tanks. Ensure the solution is sufficiently agitated. * The concentration is not even. Install the tank in a location where the concentration becomes even.
C
clesterAug 27, 2025
What to do if horiba HP-200 shows E-12 (electrode sensitivity error)?
- A
  amyhuffAug 28, 2025
  The E-12 error indicates an electrode sensitivity issue. Here's what you can do: * Clean the electrode. * If the glass electrode is broken, replace it. * If the electrode has an internal solution adding type, add the internal solution if its level is low. * For the internal solution non-adding type, replace the electrode if no white powder is seen in the solution. * If the internal solution shows discoloration or deterioration, change the whole internal solution. * If you are using an old standard solution, perform calibration using a new standard solution. * Use an appropriate standard solution.
N
Nicholas FloresAug 29, 2025
How to fix E-21 (temperature sensor disconnection error) on Horiba Measuring Instruments?
- J
  Jodi UnderwoodAug 30, 2025
  The E-21 error indicates a temperature sensor disconnection. Resolve it by: * Checking the resistance between terminals T and T of the electrode. If the resistance value is abnormal, replace the faulty electrode. * If the electrode has no temperature sensor, set the sensor type to "non." * Verifying the wiring between T and T to ensure there are no open connections in the electrode cable or relay cable.
A
Andrea ScottAug 31, 2025
What causes abnormal operation in Horiba Measuring Instruments?
- C
  Casey JohnsonAug 31, 2025
  Abnormal operation can be caused by the circuit board corroded by corrosive gas. Send clean instrumentation air from the air purge inlet.
A
Alan CampbellSep 1, 2025
How to fix E-22 (temperature sensor short-circuit error) on horiba HP-200?
- L
  Lisa HamiltonSep 2, 2025
  The E-22 error indicates a temperature sensor short-circuit. Resolve it by: * Checking the resistance between terminals T and T of the electrode. If the resistance value is abnormal, replace the faulty electrode. * Verifying the wiring between T and T to ensure there are no short-circuits in the electrode cable or relay cable.
E
Edward RamosSep 3, 2025
How to fix E-25 (temperature measurement range error) on horiba HP-200 Measuring Instruments?
- R
  reynoldsloriSep 3, 2025
  The E-25 error indicates a temperature measurement range error. Resolve it by: * Ensuring that the temperature of the solution falls within the operating temperature range of the electrode. * Setting the temperature sensor to the correct type. * If the resistance of the temperature electrode is abnormal, replace the faulty temperature electrode.
P
perkinschelseaSep 5, 2025
How to fix E-27 (temperature calibration error) on horiba HP-200?
- V
  vrodgersSep 5, 2025
  The E-27 error indicates a temperature calibration error. Resolve it by: * Ensuring that the temperature of the solution falls within the operating temperature range of the electrode. * Setting the temperature sensor to the correct type. * If the temperature electrode's resistance is abnormal, replace the faulty temperature electrode.

horiba HP-200 Specifications

General

Resolution (pH)	0.01 pH
Measurement Principle	Electrochemical
Type	Portable pH Meter
pH measurement range	0 to 14 pH
Operating Temperature	0 to 50 °C
Measurement Range (Permeation)	Not Applicable
Accuracy (Permeation)	Not Applicable