Hotpoint LSTB 4B00 User Manual (English)

Questions and Answers:

S
Scott JohnsonAug 14, 2025
Why my Hotpoint LSTB 4B00 does not start?
- M
  Marissa WaltonAug 15, 2025
  If your Hotpoint dishwasher does not start or cannot be controlled, there are several possible reasons. First, ensure that the water supply tap is turned on. Then, switch off the appliance by pressing the ON/OFF button, wait approximately one minute, and switch it back on to reset the wash cycle. Also, make sure the appliance is properly plugged in or try another electricity socket. Finally, ensure that the dishwasher door is fully closed.
R
rileyjoshuaAug 18, 2025
What to do if no water drain out of the Hotpoint Dishwasher?
- G
  Gabriela CrawfordAug 18, 2025
  If your Hotpoint dishwasher is not draining water, it could be due to several reasons. First, ensure that the wash cycle has finished. Check if the water drain hose is bent. Also, the drain duct or the filter might be clogged up with food residues. Finally, check the height of the drain hose.
E
Emily GarciaAug 21, 2025
How to fix the problem when Hotpoint LSTB 4B00 Dishwasher doesn't clean dishes properly?
- A
  Amanda Anderson DVMAug 21, 2025
  If your Hotpoint dishwasher is not cleaning dishes properly, it could be due to several reasons. Ensure that the crockery has been arranged properly and that the spray arms can rotate freely. Check if the wash cycle is too gentle. Make sure that the detergent has been measured out correctly and is suitable for use in dishwashers. Ensure that the lid on the rinse aid compartment has been closed correctly. Also, the filter may be dirty or clogged up, or the refined salt level may be low. Check that the height of the dishes is compatible with the rack adjustment and that the holes in the spray arms are not clogged.
I
icontrerasAug 25, 2025
Why is the crockery not drying properly in my Hotpoint LSTB 4B00 Dishwasher?
- J
  Judy MartinezAug 25, 2025
  If your crockery has not been dried properly after using your Hotpoint dishwasher, it could be due to several reasons. You may have selected a wash cycle without a drying programme. Also, the rinse aid may have been used up, or the rinse aid dispenser setting may not be suitable. Note that if the crockery is made from non-stick material or plastic, the presence of water drops is normal.
M
michaelaguilarAug 28, 2025
What to do if Hotpoint LSTB 4B00 won’t load any water and is blocked with flashing lights?
- M
  Mark OrtizAug 28, 2025
  If your Hotpoint dishwasher won’t load any water and shows flashing lights, it could be due to several reasons. First, ensure that there is water in the mains supply and that the tap is open. Check if the water inlet hose is bent. Also, the filters or the drain duct might be clogged and need cleaning. After checking and cleaning, switch the dishwasher on and off and start a new wash cycle. If the problem persists, turn off the water tap, remove the plug and call the Service Centre.
D
Daniel Tate MDAug 31, 2025
Why is my Hotpoint LSTB 4B00 making excessive noise?
- M
  monica03Aug 31, 2025
  If your Hotpoint dishwasher is making excessive noise, it could be due to the dishes rattling against each other or against the spray arms. Ensure that the dishes are placed properly and that the spray arms can rotate freely. Also, excessive foam from using too much detergent or unsuitable detergent can cause noise. Avoid pre-washing dishes by hand.
T
Tyrone DaviesSep 4, 2025
What to do if the Hotpoint LSTB 4B00 Dishwasher door won’t close?
- T
  tammyruizSep 4, 2025
  If your Hotpoint dishwasher door won’t close, ensure that the racks are fully inserted. Also, make sure that the lock was released. Strongly push the door until a “clacking” noise is heard.
T
Tyler AlvaradoSep 7, 2025
Why are the dishes and glasses covered in a white film after using my Hotpoint LSTB 4B00 Dishwasher?
- B
  Brandi NguyenSep 7, 2025
  If your dishes and glasses are covered in a white film or limescale deposits after using your Hotpoint dishwasher, it could be due to several reasons. Make sure you are using refined salt. Adjust the water hardness setting to a suitable level. Ensure that the salt and rinse-aid dispenser cap is closed properly. Check if the rinse aid has been used up or if the dosage is too low.
J
joegregorySep 12, 2025
Why are the dishes and glasses streaked after using my Hotpoint LSTB 4B00 Dishwasher?
- P
  Paige BowersSep 12, 2025
  If your dishes and glasses are streaked or have a bluish tinge after using your Hotpoint dishwasher, it could be because the rinse aid dosage is too high.