19
Operations
To Start
WARNING: Risk of injection or severe injury - Keep
clear of nozzle - DO NOT direct discharge stream at
persons - This machine is to be used only by
qualified operators.
AVERTISSEMENT: Risque d’injection et de
blessures graves. Se tenir à l’écart du jet. ne pas
diriger le jet de sortie vers d’autres personnes.
Confier l’utilisation de ce matériel à un opérateur
qualifié.
WARNING: Wear eye, ear, hand, foot and skin
protection at all times while operating pressure
washer.
AVERTISSEMENT: Porter une protection des yeux,
des mains, des pieds et de la peau en tout temps en
utilisant la laveuse à pression.
WARNING: Before changing pressure nozzle,
engage manual trigger gun lock.
AVERTISSEMENT: Avant de changer le buse de
projection, engager le dispositif de verrouillage
manuel du pistolet à gâchette.
IMPORTANT: The water must be turned on before
starting. Running the pump dry will cause damage
and void warranty.
IMPORTANT: Do not allow the machine to run with
trigger of the trigger gun released for more than 10
minutes at any one time or damage to pump may
occur.
1. Turn ON water supply.
2. Turn ON gas supply.
3. Hold wand firmly, release trigger of trigger gun and
turn pump switch ON. Squeeze trigger of trigger
gun and allow air to purge from system.
4. If HOT water is desired, adjust the thermostat to
the proper temperature and turn burner switch ON.
Squeeze trigger of trigger gun. The pilot will auto-
matically light, quickly followed by the firing of the
burner ring. When the trigger of the trigger gun is
released or when the thermostat temperature
setting is reached, the burner will automatically
turn off.
IMPORTANT: If ignition or flame failure is experi-
enced, discontinue use of pressure washer at once.
Turn off burner and shut off fuel supply. Have
cause of failure corrected by an authorized service
technician before use of pressure washer is
continued.
To Clean
WARNING: Risk of injection or severe injury - Keep
clear of nozzle - DO NOT direct discharge stream at
persons - This machine is to be used only by
qualified operators.
AVERTISSEMENT: Risque d’injection et de
blessures graves. Se tenir à l’écart du jet. ne pas
diriger le jet de sortie vers d’autres personnes.
Confier l’utilisation de ce matériel à un opérateur
qualifié.
1. Insert detergent inlet line into container of mixed
detergent. Open detergent ON/OFF valve. The
detergent will be pulled automatically into the
system. Allow detergent to reach end of wand
before proceeding to step 3.
2. Select pressure nozzle with spray pattern that
matches your cleaning needs. Engage manual
trigger lock and install selected nozzle.
3. Wash from the bottom to the top, using side to side
motions. This washes away heavy dirt and allows
the detergent to soak as you work toward the top.
4. Do not wash at a 90°
angle to the work (straight at
it). This will allow water to splash back at you and
reduces your cleaning power. Wash at a 30° to 60°
angle to the work. This will allow the water to splash
away from you and the water will wash the dirt away
faster and easier.
5. Use the width of the spray pattern to wash in a
wide path. Overlap spray paths for complete
coverage. Wash from side to side, using slow,
steady motions.
6. The nozzle should be 12" to 24" from work, closer
for tough areas. Be careful on painted or delicate
surfaces, the pressure may damage surface if
nozzle is too close.
7. Small parts should be washed in a basket and
larger, lightweight parts should be clamped down
so the pressure does not push them away.
8. Close the detergent ON/OFF valve to permit rinse.
Always rinse with cold water after using detergents.
Rinse from the top to the bottom to prevent
detergent from dripping onto a rinsed area. For the
best results, contact your Hotsy dealer to help you
select the best detergent for your application.
Hotsy 900/1400 Operator’s Manual 9.803-325.0 - C
To Next Page
Loading...
Need help?
General
