HotWire HWGL2 - User Manual

Hotwire Thermostat
Instructions
AUSTRALIA
Hotwire Heating
WWW.HOTWIREHEATING.COM.AU
NEW ZEALAND
The Heating Company
www.theheatingcompany.co.nz/
Model Number: HWGL2 Dual Device Thermostat
Menu #
Feature Explanation
Adjustment
(Press up & down buttons to adjust)
1 Mode/Sensor Selection
This thermostat is a combination model which allows you
to choose 3 different modes.
A mode = Air Sensing Only(Has built in sensor)
AF mode = Air & Floor sensing (Floor probe must be installed)
F mode = Floor Sensing(Floor probe must be installed)
A / AF / F
2 Switching differential
The number of degrees difference before switching.
The default is 1°C which means the thermostat will switch
the heating on 0.5°C below the set temperature and will turn
it off 0.5°C above the set temperature.With a 2°C differential
the heating will switch on 1°C below the set temperature
and will switch off 1°C above the set temperature.
1 Deg C, 2 Deg C....10 Deg C ( 1 Deg C by default)
3 Air Temp Calibration This is to recalibrate the air temp if required
-1 Deg C = decrease 1 °C , 1 Deg C = increase 1
Deg C
4 Floor Temp Calibration This is to recalibrate the floor temperature if required
-1 Deg C = decrease 1 °C , 1 Deg C = increase 1
Deg C
5
Temperature Readout
(AF mode only)
This gives you the option to show the Air Temp,
Floor Temp or to show both Air & Floor at intervals
A = Show Air Temperature
F = Show Floor Temperature
A-F = Show Floor and Air Temperature in 5 sec
intervals
6
Maximum Floor Temp
( AF Mode only)
This is to protect the floor surface 20 Deg C - 40 Deg C (40 Deg C by default)
7 Temperature Format
This allows the temperature to be set to show
Deg Celsius or Deg Fahrenheit
Deg C / Deg F
8
9
Frost Protection This is to avoid your room temp going below 5 DegC On = activated, Off = deactivated
10
5+2 / 7 Day mode
This allows you to programme either 5 days at once,
then the 2 days of the weekend separately,
or a full 7 days at the same time or 7 days separately.
01 = 5 + 2 Day Programming
02 = 7 Day Programming
11
Auto/Manual mode
selection
This allows you to choose Auto / Manual mode
00 = Auto mode
01 = Manual mode
12
Software version This is for review only V1.0
13
Minimum temperature
limit
This gives you the option to change the minimum set
temperature
5 °C~ 20 °C (5 °C by default)
40 °C~ 90 °C (40 °C by default)
14
Maximum temperature
limit
This gives you the option to change the maximum set
temperature
15
Sensor type selection This allows you to match your ther
This allows you to adjust the brightness of the back light
mostat to different sensor
10 = NTC10K(by default), 100= NTC100K,
10%~100% 100 = 100%(by default)
3=NTC3K
16
Backlit brightness
Direction of installation
17
Reset This allows you to reset your the
This allows you to choose to install your thermostat vertically or horizontally
rmostat to factory default Press and hold down button until you see RE on screen
L = Vertical H= horizontal
Hotwire Thermostat
Technical Information
To enter into the setting menu please follow the steps below:
Step 1. Turn the thermostat off by pressing
Step 2. Press you will then see menu 1.(Press and hold for about 5 seconds, you will see menu 12)
Step 3. Use the increase and decrease arrows to adjust the sensor selection which is Menu 1(Air sensing;Air and Floor, or Floor only)
Step 4. Press to move to the next Menu and once you have all the menu options set,
press to accept and store.
Configuration Menu

Summary

Configuration Menu

Mode;Sensor Selection

Allows selection of Air, Air & Floor, or Floor sensing modes for thermostat operation.

Switching differential

Sets the temperature difference before the heating switches on and off.

Air Temp Calibration

Recalibrates the air temperature reading if it deviates from the actual ambient temperature.

Floor Temp Calibration

Recalibrates the floor temperature reading if it deviates from the actual floor temperature.

Temperature Readout

Allows selection to display Air Temp, Floor Temp, or both at intervals (AF mode only).

Maximum Floor Temp

Protects the floor surface by setting a maximum temperature limit (AF mode only).

Temperature Format

Sets the temperature display to show in Celsius or Fahrenheit.

Frost Protection

Prevents the room temperature from dropping below 5°C by activating heating.

5+2; 7 Day mode

Allows programming for 5 weekdays and 2 weekend days, or a full 7 days.

Auto;Manual mode selection

Enables selection between automatic programmed schedules or manual temperature control.

Minimum temperature limit

Sets the lowest allowable temperature the thermostat can be set to.

Maximum temperature limit

Sets the highest allowable temperature the thermostat can be set to.

Sensor type selection

Matches the thermostat to the specific type of floor sensor being used.

Backlit brightness

Allows adjustment of the brightness level of the thermostat's backlight.

Reset

Resets the thermostat to its original factory default settings.

Direction of installation

Selects the thermostat's orientation for installation, vertical or horizontal.

Programming your Thermostat

Setting the clock and day of the week

Ensures accurate scheduling by setting the current time and day.

Setting the Programme Schedules

Details how to program daily heating schedules for optimal comfort and efficiency.

Installation and Wiring

Change between Manual and Auto Mode

Switches thermostat operation between automatic programming and manual control.

Lock the Keypad

Secures the thermostat controls to prevent unintended adjustments.

Reset to Factory Setting

Restores the thermostat to its original default configuration.

HotWire HWGL2 Specifications

General

Brand	HotWire
Model	HWGL2
Category	Thermostat
Language	English