HP 4400 User Manual (English)

Other manuals for HP 4400

Software Guide77 pages

Quickspecs31 pages

Replacement Instructions5 pages

Assembly Replacement Instructions3 pages

Questions and Answers:

K
katelynhartAug 20, 2025
What to do if I get HTTP status 404 or 503 error on my HP Server?
- G
  ggeorgeAug 21, 2025
  If you encounter an HTTP status 404 (Not Found) or 503 (No Service) error when accessing your HP P6000 Server, here's what you can do: * For a 404 error, if it occurs because HP P6000 Command View might be initializing, retry the request by refreshing the browser. * If a .frm (HTML) file is missing, reinstall HP P6000 Command View. * For a 503 error, retry the request when HP P6000 Command View is up. * If the browser times out, retry the request when both the server and HP P6000 Command View are running.
M
melissaandersonAug 22, 2025
Why does my HP Server show an unknown storage system?
- A
  Andre SpenceAug 22, 2025
  If your HP P6000 Command View reports an unknown storage system, it might be due to a communication loss with the controllers. If the array has a heavy I/O load, the HBA in the management server may time out commands to the controllers, making the array appear in an unknown state. This usually corrects itself within a minute. Alternatively, you can perform a Rediscover operation to initiate new commands to the controller. Also, ensure you're using an HP P6000 Command View version compatible with XCS 10000000. If not, upgrade HP P6000 Command View to a compatible version.
J
jason52Aug 27, 2025
How to fix 'View is not set or view list is null' error on HP Server?
- D
  dmurrayAug 27, 2025
  If the HP P6000 Command View cannot build the view of the array, click OK, wait one to five minutes, and retry the command. If you still cannot see the array, stop and restart HP P6000 Command View.
R
Richard JohnsonAug 28, 2025
What to do if drive code load fails to write firmware to drive buffer on HP Server?
- T
  Tiffany HarrisonAug 28, 2025
  If the drive code load fails to write firmware to the drive buffer on your HP Server, check the drive properties in HP P6000 Command View for problems. Resolve any identified issues, and then restart the disk drive firmware upgrade.
E
emunozAug 29, 2025
What to do if disk cannot be code loaded because it is part of a group on HP Server?
- P
  Peter YoungAug 29, 2025
  If the disk cannot be code loaded because it is part of a group on your HP Server, restart the disk drive firmware upgrade.
P
pamelamosesAug 31, 2025
What to do if disk group has background reconstructing in progress on HP Server?
- L
  Linda ArcherAug 31, 2025
  If the disk group containing the physical store has background reconstructing or reverting in progress on your HP Server, reduce the I/O using the I/O analysis for the online disk drive firmware upgrade, and then restart the upgrade.
B
bmacdonaldSep 2, 2025
What to do if unable to determine the condition of the volume on HP Server?
- T
  Tammy MckeeSep 2, 2025
  If the condition of the volume cannot be determined during a drive code load on your HP Server, check the drive properties in HP P6000 Command View for problems. Resolve any issues and restart the disk drive firmware upgrade.
N
Nancy WestSep 3, 2025
What to do if the disk cannot be code loaded because disk is part of a RAID0 group on HP Server?
- K
  Kayla MooreSep 4, 2025
  If the disk cannot be code loaded because disk is part of a RAID0 group on your HP Server, remove disks that contain RAID0 (Vraid0) data from the group and restart the disk drive firmware upgrade.
M
Mrs. Lisa JohnsonSep 5, 2025
What to do if the storage cell is in device discovery on HP Server?
- E
  Eric MartinSep 5, 2025
  If the storage cell is in device discovery on your HP Server, restart the disk drive firmware upgrade.
C
Caitlin MedinaSep 7, 2025
What to do if I get a 'Media Not Available' error on my HP Server?
- A
  Andrea PalmerSep 7, 2025
  If you encounter a 'Media Not Available' error on your HP Server, restart the disk drive firmware upgrade.