HP 501 802.11ac Wireless Client Bridge Quickstart 7 HP 501 antennas
3. Reconnect power to the HP 501.
4. Reconnect your computer to the HP 501.
5. Confirm that your wireless network interface is still disabled (it was
disabled during an earlier configuration step).
6. Enable the Ethernet network interface of your computer, and verify that it
is set to obtain an IP address automatically from DHCP.
7. Confirm that you can browse the Internet from your computer.
G. To perform additional configuration
Re-launch the HP 501 management tool at https://<IP address> where
<IP address> is the IP address that was obtained by the HP 501 from the DHCP
server or that was statically configured in the HP 501 (see section D above).
HP 501 antennas
The following antennas are approved for use with the HP 501:
*Antennas included with the HP 501.
Note:
In the US, channels in the 5150-5250 MHz band are disabled when the
HP 501 is configured for use with the J9170A antenna.
Note:
When using any of the optional high-gain antennas, the installer must
also provide a cable that connects the HP 501 RP-SMA connector to the
Type N connector on the optional antenna.
Caution:
When installing outdoor antennas outside, ensure that the metal
shield is reliably connected to the protective earthing system of the building.
Technical support
For worldwide technical support information, see the HP support website at
http://www.hp.com/support.
For more information see "Contacting HP" in the HP 501 802.11ac Wireless
Client Bridge Installation Guide.
Other regulatory information
For important safety, environmental, and regulatory information, see Safety and
Compliance Information for Server, Storage, Power, Networking, and Rack
Products, available at http://www.hp.com/support/Safety-Compliance-
EnterpriseProducts.
FCC Notice
Contains TX FCC ID: B94MRLBB1301
This FCC Class B device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received, including
interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The FCC requires the user to be notified that any changes or modifications
made to the device that are not expressly approved by the Hewlett-Packard
Company may void the user's authority to operate the equipment.
For products available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co-located with any other
transmitters except in accordance with FCC multi-transmitter product
procedures.
Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s)
can be operated simultaneously without C2P.
Part Type Band Gain Use Elements
5188-
9334*
Omnidirectional 2.4/5 GHz 1.8/2 dBi Indoor 1
J9170A Directional 2.4/5 GHz 10.9/13.5 dBi Outdoor 3
J9719A Omnidirectional 2.4 GHz 6 dBi Outdoor 3
J9720A Omnidirectional 5 GHz 8 dBi Outdoor 3
To Next Page
Loading...
