HP 8673C - Contents

HP 8673C/D COntents
CONTENTS
Sectlon I
GENERAL INFORMATION
Page
Introduction ...................................... 1-l
Specifications .................................... 1-l
Safety Considerations ............................ 1-1
Instrumenta Covered by this Manual .............. 1-I
Manual Changes Supplement ..................... 1-I
Deecxiption.......................................1.2
Options .......................................... 1.2
Electrical Options ..............................
1-2
Mechanical Options ............................ 1-3
Accessories Supplied ............................. l-3
Equipment Required but not Supplied ............. 1-3
Electrical Equipment Available ................... 1-3
Recommended ‘I&t Equipment .................... l-3
Section II
INSTALLATION
Introduction ..................................... .2-l
Initial Inspection ................................ .2-l
Preparation for Use ............................. ,2-l
Power Requirements. .......................... .2-l
Line Voltage and Fuse Selectmn ................ 2-I
PowerCables................................... -I
HP.IB Address Selection ........................ %2
Interconnections ............................... %3
Mating Connectors ............................. %3
operating Environment ........................ %4
Bench Operation ............................... %4
Rack Mounting ................................ .2-4
Storage and Shipment ........................... .2-4
Environment .................................. .2.4
Packaging ................................... ..2 -4
Section Ill
OPERATION
Introduction......................................a- 1
Operating Characteristics ..................... .3-l
Local Operation ................................ Sl
Remote Operation ............................. .51
Operator’sChecks..............................& 1
Operator’s Maintenance ....................... .51
General Instructions ............................. .3-4
nm-On ....................................... .3-4
Frequency Standard Selection ................. .3-4
Additional Operating Information ............... .3-6
AutoPeak........................................3 -6
Pulse Mode. ..................................... .3-6
ALC (Automatic Level Control) .................. .3-6
SweepMode...................................... -6
Operator’s Checks .............................. ,514
Basic Functional Checks ..................... ,914
HP-IB Functional Checks ..................... ,523
Page
Remote Operation, Auxiliary Control ............. $30
Remote and Local Messages and the
AUX Input Lines ............................. ,3-30
AUX Output Lines ........................... .3-30
R&mote Operation HewlettiPackard
Interface Bus .................................. .3-31
HP-IB Compatibility ......................... .3-31
Remote Mode ................................. ,331
Local Mode,, ................................. ,331
Addressing .................................... $33
Turn-on Default Condition .................... .3-34
Data Messages ............................... ,834
D’ 1 wp ays ...................................... 834
Output Level ................................. .3-34
Receiving Data Messages ..................... ,534
Sending the Data Meeeage .................... .3-35
Receiving the Clear Message .................. .3-38
Receiving the Trigger Message ................ .3-38
Receiving the Remote Message. ............... .3-38
Receiving the Local Message. ................. .3-38
Receiving the Local Lockout Message ......... .3-38
Receiting the Clear Lockout/Set Local
Message .................................... .3-38
Receiving the Pass Control Message .......... .3-39
Sending the Require Service Message ......... .3-39
Sending the Statue Byte Mesaage ............. .3-39
Clearing the Statue Byte ...................... .3-39
Sending the Status Bit Message ............... .3-40
Receiving the Abort Message ................. .3-40
Sectlon IV
PERFORMANCE TESTS, Part 1
Introduction .................................... 4-1
Equipment Required ............................ 4-1
Performance Test Record ........................ 4-1
Test Procedures ................................. 4-1
Operation Verification .......................... 4-1
Turn-on Checks ................................. 4-2
Frequency Range and Resolution ................ 4-3
output Level .................................... 4-5
Frequency and Amplitude Modulation .......... 4.13
Pulse Modulation .............................. 4-16
Section IV, Pm-l 2
PERFORMANCE TESTS, Part 2,
and
Sections V, VI, VII and VIII
ADJUSTMENTS
REPLACEABLE PARTS
MANUAL CHANGES
SERVICE
These sections are bound separately in Volume 2 with a
separate table of contents.