T
able 5-3.
Typical Calibration
Kit Standard
and
Corresponding
Number
Typical
Standard
Type
Default
Standard
Number
short
(m)
1
open (m) 2
broadband
load
3
delay/thru 4
sliding
load
5
lowband
load
6
short
(f)
7
open
(f)
8
5.
Press
the
underlined
softkey
.
F
or
example
,
if
you selected
4
1
5
4
x1
5
in
the
previous
step
,
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
SHORT
should
be
the
underlined
softkey
.
Note
Do
not
press
a
softkey
that
is
not
underlined
unless
you
want
to
change
the
\type"
of
standard.
6.
This
step applies
only to
the
open
.
Go
to
the
next
step
if
you
selected
any
other
standard.
a.
Press
N
N
N
N
N
N
N
N
N
N
N
N
N
N
OPEN
N
N
N
N
N
N
N
N
C0
.
Observe
the
value
on
the
analyzer
screen.
Use
the entry
keys
on
the
analyzer
front
panel to
change
the
value
.
b.
Repeat
the modication
for
N
N
N
N
N
NN
N
C1
,
N
N
N
N
N
NN
N
C2
, and
N
N
N
N
N
NN
N
C3
.
7.
This
step
applies
only
to
the
load
.
Go
to
the
next
step
if you
selected any
other
standard.
Ensure
that
the
correct
load
type
is
underlined:
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
FIXED
,
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
SLIDING
,
or
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
OFFSET
.
8.
Press
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
SPECIFY OFFSET
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
OFFSET DELAY
and
observe
the
value
on
the
analyzer
screen.
T
o
change
the
value
,
use
the
entry
keys
on
the
front
panel.
9.
Repeat
the
value
modication
for
the
characteristics
listed
below:
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
OFFSET
LOSS
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
OFFSET Z0
NNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNNN
NNNNNNN
MINIMUM FREQUENCY
NNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNN
MAXIMUM FREQUENCY
10.
Ensure that the correct transmission line is underlined:
N
NNNNNNNNNNNNN
COAX
or
N
NNNNNNNNNNNNNNNNNNNNNNNNN
NNN
WAVEGUIDE
.
11.
Press
NNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNNN
N
STD OFFSET DONE
NNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNN
STD DONE (DEFINED)
.
12. Repeat steps 4 through 11 for the remaining standards.
Optimizing Measurement Results 5-27
To Next Page
Loading...
