HP A Series User Manual

2-15 INPUT POWER REQUIREMENTS
2-16 The modular power supplies may be operated
from a nominal 120 Vac, 220 Vac, or 240 Vac,
48-63 Hz, power source. The standard supply (no
options) is shipped from the factory wired for 120 Vac
(nominal) operation and requires the following maxi¬
mum input current and power at high line (127 Vac)
voltage input:
AC INPUT at 127 Vac
MODEL
CURRENT
(Max.)
POWER
(Max.)
62003A
.30A
31W
62003C
.77A
74W
62003E
1.38A
143W
62004A
.33A
34W
62004C
.78A
76W
62004E
1.42A
149W
62005A
.37A
37W
62005C
.80A
79W
62005E
1.53A
160W
62006A
.36A
37W
62006C
.80A
79W
62006E
1.56A
161W
6201OA
.39A
39W
62010C
.98A
97W
62010E
1.87A
192W
52012A
.47A
47W
62012C
1.00A
100W
62012E
1.89A
191W
62015A
.45A
46W
62015C
.99A
97W
62015E
1.82A
181W
62018A
.42A
42W
62018C
.97A
95W
62018E
1.93A
196W
62024A
.39A
39W
62024C
.93A
88W
62024E
1.95A
198W
62028A
.44A
44W
62028C
.91 A
86W
62028E
1.87A
190W
62048A
.47 A
47W
62048C
.97A
95W
62048E
2.00A
193W
2-17 220/240 VOLT OPERATION
2-18 As applicable, Options 101,102, and 103 (in¬
stalled at the factory) permit the supply to be operated
from a 120, 220, or 240 Vac (nominal) input line.
Option 101 provides for 220 Vac operation while
Option 102 allows 240 Vac operation. Option 103,
however, provides for either 120 Vac or 240 Vac oper¬
ation at the selection of the user as described below.
2-19 Option 103 Power Transformer Connections,
A— suffix Models. For the A- suffix models, the pri¬
mary connections of the supply are changed at the in¬
board side of the rear power input terminals. For
120 Vac operation (as shipped), two leads are soldered
from each of the ac input terminals as shown in
Figure 2-2B. To connect the supply for 240 Vac oper¬
ation, unsolder the wht/bik/yel and wht/blk/grn leads
and twist them together with a wire terminal as shown
in Figure 2-2A.
Figure 2-2. Primary Connections For 120/240 Vac
Operation (Option 103) — A Suffix Models Only
2-20 Option 103 Power Transformer Connections,
-C and E- Suffix Models. For the C- and E- suffix
models, the appropriate power transformer 120/240 V
terminals must be connected as shown in Figure 2-3.
Notice that the transformer connections are changed
at the transformer terminals shown in the illustration.
2-3

HP A Series Specifications

General

Model	HP A Series
Category	Power Supply
Input Voltage	100-240V AC
Input Frequency	50/60 Hz
Cooling	Fan
Connectors	SATA, Molex
Efficiency	80% or higher (80 Plus Certified)