Configuring Information
Configuring InformationConfiguring Information
Configuring Information
Memory Channel adapters (CCMAB-BA) must be configured in 5-volt PCI slots.
Up to two PCI-to-System Area Network adapters (CCMAB-BA) are supported in a single system.
Two-node clusters can be configured by ordering a CCMAB-BA for each node and one
BN39B-04 or BN39B-10 cable; cable connects directly to CCMAB-BA in each node.
For a two-node cluster that will not need to be rebooted when adding additional members,
order one CCMAB-BA adapter and one BN39B-04 or BN39B-10 cable for each node, and
one CCMHB-AA hub for the cluster.
For three- or four- node clusters, order one CCMAB-BA adapter and one BN39B-04 or
BN39B-10 cable for each node, and one CCMHB-AA hub for the cluster. If two CCMAB-BAs
are configured in each system, a second CCMHB-AA is required.
CCMHB-AA includes four CCMLB-AA line cards and supports up to four nodes; expansion up
to eight system nodes can be achieved by adding up to four CCMLB-AA line cards.
If nodes must be separated by a distance longer than standard copper cables allow the
CCMFB option converts the output of the standard CCMAB controller or CCMLB line card to
single-mode fiber optic cable. The fiber optic connection may be up to 2,000 meters long
between two CCMAB controllers connected in virtual hub mode, or 3,000 meters between a
CCMAB controller and a CCMHB hub. (The connection from the CCMHB hub to a second
system may also be 3,000 meters.) The CCMFB option requires a second PCI slot in the system
from which it draws power only. It is normally connected to the corresponding CCMAB
controller with the short BN39B-01 cable. The CCMFB is also used in the CCMHB hub where it
occupies a slot normally used by the CCMLB line card, limiting expansion to four radial fiber
optic connections.
CCMHB-BA hub expansion box provides additional slots for up to eight fiber optic connections.
Two standard length single-mode fiber optic cables are available (BN34R-10 and BN34R-31);
however, users normally provide this fiber optic connection. Fiber optic connectivity is
completely transparent to the systems using it and has no performance impact.
NOTE:
NOTE: NOTE:
NOTE:
When configuring with two Memory Channel Controllers (CCMAB-BA), all nodes in a
Memory Channel cluster must have the window size jumper set to the same size, specifically 128
MEMORY CHANNEL
MEMORY CHANNELMEMORY CHANNEL
MEMORY CHANNEL
Controller/ System Area
Controller/ System AreaController/ System Area
Controller/ System Area
Network Hub
Network HubNetwork Hub
Network Hub
PCI-to-System Area Network Controller, maximum two -- 5V/3.3V
CCMAB-BA
System Area Network Hub with four line cards; includes BN19P-2E power cord for
Canada, Japan, and U.S. - for other regions, order appropriate power cord from the
following list:
CCMHB-AA
Hub expansion box with no line cards
CCMHB-BA
Expansion line card for CCMHB hub
CCMLB-AA
1-meter cable for CCMAB and CCMHB
BN39B-01
4-meter cable for CCMAB and CCMHB
BN39B-04
10-meter cable for CCMAB and CCMHB
BN39B-10
Copper-to-single mode fiber optic converter
–
––
–
5V/3.3V (clock not affected); maximum
two per system.
CCMFB-BA
QuickSpecs
HP AlphaServer DS25 HP AlphaStation DS25
HP AlphaServer DS25 HP AlphaStation DS25HP AlphaServer DS25 HP AlphaStation DS25
HP AlphaServer DS25 HP AlphaStation DS25
Options
DA - 11432 Worldwide — Version 21 — May 7, 2007
Page 18
To Next Page
Loading...
