To Next Page

To Previous Page

[MCE-Vlan-interface10] quit

# Configure VLAN 20, add port Ten-GigabitEthernet 1/0/2 to VLAN 20.

[MCE] vlan 20

[MCE-vlan20] port ten-gigabitethernet 1/0/2

[MCE-vlan20] quit

# Bind VLAN-interface 20 to VPN instance vpn2.

[MCE] interface vlan-interface 20

[MCE-Vlan-interface20] ip binding vpn-instance vpn2

# Specify an IP address for VLAN-interface 20.

[MCE-Vlan-interface20] ip address 10.214.20.3 24

[MCE-Vlan-interface20] quit

# On PE 1, configure VPN instances vpn1 and vpn2, and specify an RD and route targets for

each VPN instance.

<PE1> system-view

[PE1] ip vpn-instance vpn1

[PE1-vpn-instance-vpn1] route-distinguisher 10:1

[PE1-vpn-instance-vpn1] vpn-target 10:1

[PE1-vpn-instance-vpn1] quit

[PE1] ip vpn-instance vpn2

[PE1-vpn-instance-vpn2] route-distinguisher 20:1

[PE1-vpn-instance-vpn2] vpn-target 20:1

[PE1-vpn-instance-vpn2] quit

2. Configure routing between the MCE and VPN sites:

The MCE is connected to VPN 1 directly, and no routing protocol is enabled in VPN 1.

Therefore, you can configure static routes.

# On VR 1, assign IP address 10.214.10.2/24 to the interface connected to MCE and

192.168.0.1/24 to the interface connected to VPN 1. Add ports to VLANs correctly. (Details not

shown.)

# On VR 1, configure a default route with the next hop being 10.214.10.3.

<VR1> system-view

[VR1] ip route-static 0.0.0.0 0.0.0.0 10.214.10.3

# On the MCE, configure a static route to 192.168.0.0/24 with the next hop 10.214.10.2. Bind

the static route to VPN instance vpn1.

[MCE] ip route-static vpn-instance vpn1 192.168.0.0 24 10.214.10.2

# On the MCE, display the routing information maintained for VPN instance vpn1.

[MCE] display ip routing-table vpn-instance vpn1

Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

10.214.10.0/24 Direct 0 0 10.214.10.3 Vlan10

10.214.10.0/32 Direct 0 0 10.214.10.3 Vlan10

10.214.10.3/32 Direct 0 0 127.0.0.1 InLoop0

10.214.10.255/32 Direct 0 0 10.214.10.3 Vlan10

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 and is the answer not in the manual?

HP FlexFabric 5700 Specifications

General

Category	Switch
Power Device	Internal power supply
Model	FlexFabric 5700
Uplink Ports	4 x 10 Gigabit SFP+
Form Factor	Rack-mountable
Routing Protocol	OSPF, BGP, RIP, IS-IS, PIM, IGMP, VRRP, RIPng, OSPFv3, PIM6
Remote Management Protocol	SNMP, CLI
Features	IPv6 support, ACL, QoS, VLAN, LLDP, sFlow, RMON
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad, IEEE 802.3x
Power Redundancy	Yes
Operating Temperature	0 °C to 45 °C
Operating Humidity	10% to 90% non-condensing
MAC Address Table Size	32K entries