HP FlexFabric 5700 User Manual

39
Interface : Vlan20 Cost : 0
Destination: 2002:1::1/128 Protocol : Direct
NextHop : ::1 Preference: 0
Interface : InLoop0 Cost : 0
Destination: 2012::/64 Protocol : RIPng
NextHop : FE80::20C:29FF:FE40:701 Preference: 100
Interface : Vlan20 Cost : 1
Destination: FE80::/10 Protocol : Direct
NextHop : :: Preference: 0
Interface : NULL0 Cost : 0
Destination: FF00::/8 Protocol : Direct
NextHop : :: Preference: 0
Interface : NULL0 Cost : 0
The output shows that the MCE has learned the private route of VPN 2. The MCE maintains the
routes of VPN 1 and VPN 2 in two different routing tables. In this way, routes from different
VPNs are separated.
3. Configure routing between the MCE and PE 1:
# On the MCE, configure the port connected to PE 1 as a trunk port, and configure it to permit
packets of VLAN 30 and VLAN 40 to pass with VLAN tags.
[MCE] interface ten-gigabitethernet 1/0/3
[MCE-Ten-GigabitEthernet1/0/3] port link-type trunk
[MCE-Ten-GigabitEthernet1/0/3] port trunk permit vlan 30 40
[MCE-Ten-GigabitEthernet1/0/3] quit
# On PE 1, configure the port connected to MCE as a trunk port, and configure it to permit
packets of VLAN 30 and VLAN 40 to pass with VLAN tags.
[PE1] interface ten-gigabitethernet 1/0/1
[PE1-Ten-GigabitEthernet1/0/1] port link-type trunk
[PE1-Ten-GigabitEthernet1/0/1] port trunk permit vlan 30 40
[PE1-Ten-GigabitEthernet1/0/1] quit
# On the MCE, create VLAN 30 and VLAN-interface 30, bind VLAN-interface 30 to VPN
instance vpn1, and configure an IPv6 address for the VLAN-interface 30.
[MCE] vlan 30
[MCE-vlan30] quit
[MCE] interface vlan-interface 30
[MCE-Vlan-interface30] ip binding vpn-instance vpn1
[MCE-Vlan-interface30] ipv6 address 30::1 64
[MCE-Vlan-interface30] quit
# On the MCE, create VLAN 40 and VLAN-interface 40, bind VLAN-interface 40 to VPN
instance vpn2, and configure an IPv6 address for the VLAN-interface 40.
[MCE] vlan 40
[MCE-vlan40] quit
[MCE] interface vlan-interface 40
[MCE-Vlan-interface40] ip binding vpn-instance vpn2
[MCE-Vlan-interface40] ipv6 address 40::1 64
[MCE-Vlan-interface40] quit

HP FlexFabric 5700 Specifications

General

Category	Switch
Power Device	Internal power supply
Model	FlexFabric 5700
Uplink Ports	4 x 10 Gigabit SFP+
Form Factor	Rack-mountable
Routing Protocol	OSPF, BGP, RIP, IS-IS, PIM, IGMP, VRRP, RIPng, OSPFv3, PIM6
Remote Management Protocol	SNMP, CLI
Features	IPv6 support, ACL, QoS, VLAN, LLDP, sFlow, RMON
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad, IEEE 802.3x
Power Redundancy	Yes
Operating Temperature	0 °C to 45 °C
Operating Humidity	10% to 90% non-condensing
MAC Address Table Size	32K entries