To Next Page

To Previous Page

# On PE 1, create VLAN 30 and VLAN-interface 30, bind VLAN-interface 30 to VPN instance

vpn1, and configure an IPv6 address for the VLAN-interface 30.

[PE1] vlan 30

[PE1-vlan30] quit

[PE1] interface vlan-interface 30

[PE1-Vlan-interface30] ip binding vpn-instance vpn1

[PE1-Vlan-interface30] ipv6 address 30::2 64

[PE1-Vlan-interface30] quit

# On PE 1, create VLAN 40 and VLAN-interface 40, bind VLAN-interface 40 to VPN instance

vpn2, and configure an IPv6 address for the VLAN-interface 40.

[PE1] vlan 40

[PE1-vlan40] quit

[PE1] interface vlan-interface 40

[PE1-Vlan-interface40] ip binding vpn-instance vpn2

[PE1-Vlan-interface40] ipv6 address 40::2 64

[PE1-Vlan-interface40] quit

# Configure the IP address of the interface Loopback 0 as 101.101.10.1 for the MCE and as

100.100.10.1 for PE 1. Specify the loopback interface address as the router ID for the MCE and

PE 1. (Details not shown.)

# Enable OSPFv3 process 10 on the MCE, bind the process to VPN instance vpn1, and

redistribute the IPv6 static route of VPN 1.

[MCE] ospfv3 10 vpn-instance vpn1

[MCE-ospfv3-10] router-id 101.101.10.1

[MCE-ospfv3-10] import-route static

[MCE-ospfv3-10] quit

# Enable OSPFv3 on VLAN-interface 30.

[MCE] interface vlan-interface 30

[MCE-Vlan-interface30] ospfv3 10 area 0.0.0.0

[MCE-Vlan-interface30] quit

# On PE 1, enable OSPFv3 process 10 and bind the process to VPN instance vpn1.

[PE1] ospfv3 10 vpn-instance vpn1

[PE1-ospfv3-10] router-id 100.100.10.1

[PE1-ospfv3-10] quit

# Enable OSPFv3 on VLAN-interface 30.

[PE1] interface vlan-interface 30

[PE1-Vlan-interface30] ospfv3 10 area 0.0.0.0

[PE1-Vlan-interface30] quit

# Use similar procedures to configure OSPFv3 process 20 between the MCE and PE 1 and

redistribute VPN 2's routes from RIPng process 20 into the OSPFv3 routing table of the MCE.

(Details not shown.)

Verifying the configuration

# Display the routing table for VPN instance vpn1. The output shows that PE 1 has learned the

private route of VPN 1 through OSPFv3.

[PE1] display ipv6 routing-table vpn-instance vpn1

Destinations : 6 Routes : 6

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 and is the answer not in the manual?

HP FlexFabric 5700 Specifications

General

Category	Switch
Power Device	Internal power supply
Model	FlexFabric 5700
Uplink Ports	4 x 10 Gigabit SFP+
Form Factor	Rack-mountable
Routing Protocol	OSPF, BGP, RIP, IS-IS, PIM, IGMP, VRRP, RIPng, OSPFv3, PIM6
Remote Management Protocol	SNMP, CLI
Features	IPv6 support, ACL, QoS, VLAN, LLDP, sFlow, RMON
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad, IEEE 802.3x
Power Redundancy	Yes
Operating Temperature	0 °C to 45 °C
Operating Humidity	10% to 90% non-condensing
MAC Address Table Size	32K entries