HP LaserJet 1150 Series - Spring (Continued); Spring (Transfer Roller); External Case Parts; Cover

LaserJet 1150 series printe
r
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronics/Power Cords
Spring
24
RA0-1200-000CN Torsion spring - Provides high voltage connection to the toner cartridge (primary charging roller) - Mounts on the left rear
side of the paper feed guide assembly
25
RC1-1792-000CN Torsion spring - Functions as an electrical connection between the engine control board and the transfer roller contact
spring - Mounts in the lower right corner of the paper pick-up assembly
External Case Parts
Cover
26
RC1-1821-000CN Front cover - Lower front of printer - With opening for inserting the paper input tray assembly
27
RC1-1822-000CN Right side cover assembly - Has molded-in air intake louvers
28
RC1-1823-000CN Left side printer cover - Covers the USB and LIO port connectors (On the formatter board)
29
RC1-1852-000CN Cover Insert - Covers the unused slot under the right side plate - Mounts to the right side plate
30
RM1-0544-000CN Rear cover assembly - Includes rear cover and fold down face-up (or straight through) paper output tray (Tray is NOT
sold separately)
31
RM1-0720-000CN Top cover assembly - Has face-down paper output tray molded into it
Door
32
RM1-0543-000CN Toner cartridge door - Fold down door used when accessing the toner cartridge - Mounts to the top of the front cover
Foot
33
RA0-1003-000CN Rubber foot - Used for the rear feet on the bottom of printer - Mounts on the front bottom frame of the paper pick-up
assembly (two used)
Link
34
RA0-1023-000CN Connecting link - Connects between the sliding linkage on the left and right side plates and the toner cartridge access
door (2 used)
Pan
35
RC1-1813-000CN Support pan (case) for the engine controller PC board - Metal pan which also acts as part of the bottom of the printer
Screw
36
RY7-5082-000CN Screw kit - Includes nine bags of different size screws - This is a complete set of screws for the LaserJet 1300 series
printer
Fusing Assembly Parts
Delivery
37
RM1-0556-020CN Face-down delivery assembly - Includes the support frame, drive roller and gear, and the four spring loaded pressure
rollers - Mounts in the upper rear of the fusing assembly
Fusing Assembly
38
RM1-0560-000CN Fusing assembly - Bonds toner to paper with heat (For 100V to 120V operation) - Mounts in the upper rear of the printer
39
RM1-0561-000CN Fusing assembly - Bonds toner to paper with heat (For 220V to 240V operation) - Mounts in the upper rear of the printer
Gear
40
RA0-1088-000CN 29 tooth gear - Mounts on the end of the pressure roller - Largest of the three gears on the fusing assembly
Spring
41
RA0-1090-000CN Tension spring - Provides upward tension for the green release lever (2 used) - Mounts in the left and right rear corners
of the fusing assembly
42
RA0-1099-000CN Torsion spring - Provides a small amount of back pressure for the delivery sensor flag - mounts in the rear center of the
fusing assembly
43
RA0-1115-000CN Torsion spring - Provides pressure for the lower solid rollers on the face-down paper delivery assembly (2 used)
44
RA0-1116-000CN Torsion spring - Provides pressure for the upper serrated rollers on the face-down paper delivery assembly (2 used)
45
RU5-2140-000CN Compression spring - Provides downward pressure on each end of the fusing roller (2 used) - Mounts in the upper part
of the fusing assembly
© 2004 Hewlett-Packard 2