To Previous Page

1. ENERGY STAR® power is measured with factory defaults, brightness at ENERGY STAR® level of 200 cd/m2 and with no USB loads.

2. Default Power is measured with factory defaults, including factory default brightness and USB ports loaded at 25% of maximum.

3. Maximum Power is measured with monitor at maximum brightness and with USB ports loaded at 100% of maximum.

4. External power supplies, power cords, cables and peripherals are not Low Halogen. Service parts obtained after purchase may not be

Low Halogen.

5. The HP Quick Release has been designed to support a maximum of up to 24 lbs (10.9 kg) for all devices mounted. Because mounting

surfaces vary widely and the final mounting method and configuration may vary, mounting fasteners are not supplied (other than the

VESA-compliant screws). HP recommends that you consult with a qualified engineering, architectural or construction professional to

determine the appropriate type and quantity of mounting fasteners required for your application and to ensure that your mounting

solution is properly installed to support applied loads.

6. EPEAT® Gold where HP registers commercial display products. See

www.epeat.net

for registration status in your country.

7. Service levels and response times for HP Care Pack Services may vary depending on your geographic location. Service starts from

date of hardware purchase. Restrictions and limitations apply. See

www.hp.com/go/cpc

for details.

ENERGY STAR is a registered mark owned by the U.S. government. All specifications represent the typical specifications provided by

HP's component manufacturers; actual performance may vary either higher or lower. The only warranties for HP products and services

are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as

constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

QuickSpecs

HP Z30i 30-inch IPS Display

Technical Specifications

DA - 14755 North America — Version 3 — January 16, 2014

Page 9

Questions and Answers:

Need help?

Do you have a question about the HP Z30i and is the answer not in the manual?

HP Z30i Specifications

General

3D	No
HD type	-
Pixel pitch	0.250 x 0.250 mm
Aspect ratio	16:10
Response time	8 ms
Backlight type	W-LED
Display diagonal	30 \
Display resolution	2560 x 1600 pixels
Display technology	LED
Vertical scan range	60 - 70 Hz
Horizontal scan range	31 - 80 kHz
Contrast ratio (dynamic)	5000000:1
Contrast ratio (typical)	1000:1
Display number of colors	16.78 million colors
Digital vertical frequency	50 - 70 Hz
Digital horizontal frequency	24 - 98 kHz
Display brightness (typical)	350 cd/m²
On/off switch	Yes
USB hub version	3.2 Gen 1 (3.1 Gen 1)
DVI-I ports quantity	0
USB Type-A downstream ports quantity	5
Pivot angle	0 - 90 °
LED indicators	Power
Tilt angle range	-5 - 20 °
Cable lock slot type	Kensington
Panel mounting interface	100 x 100 mm
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	125 W
Power consumption (standby)	0.5 W
Power consumption (typical)	85 W
Certification	CE, CB, CEL, KC, KCC, NOM, PSB, ICE, TUV-S, CCC, CECP, SEPA, TCO 6.0, EPA, ISC, VCCI, FCC, HSMI
Product color	Black
Country of origin	China
Market positioning	Business
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	5 - 40 °C
Storage relative humidity (H-H)	10 - 85 %
Operating relative humidity (H-H)	20 - 80 %
Package weight	13730 g
Cables included	DisplayPort, DVI, USB
Sustainability certificates	EPEAT Gold, ENERGY STAR
Harmonized System (HS) code	85285210

Weight and Dimensions