Huawei AR1200 Series - Page 120

Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.9/32 Direct 0 0 D 127.0.0.1 LoopBack1
2.2.2.9/32 OSPF 10 2 D 10.1.1.2 GigabitEthernet1/0/0
3.3.3.9/32 OSPF 10 4 D 10.1.1.2 GigabitEthernet1/0/0
4.4.4.9/32 OSPF 10 3 D 10.1.1.2 GigabitEthernet1/0/0
10.1.1.0/30 Direct 0 0 D 10.1.1.1 GigabitEthernet1/0/0
10.1.1.1/32 Direct 0 0 D 127.0.0.1 Pos1/0/0
10.1.1.2/32 Direct 0 0 D 10.1.1.2 GigabitEthernet1/0/0
10.2.1.0/30 OSPF 10 2 D 10.1.1.2 GigabitEthernet1/0/0
10.3.1.0/30 Direct 0 0 D 10.3.1.1 GigabitEthernet2/0/0
10.3.1.1/32 Direct 0 0 D 127.0.0.1 Pos2/0/0
10.3.1.2/32 Direct 0 0 D 10.3.1.2 GigabitEthernet2/0/0
10.4.1.0/30 OSPF 10 3 D 10.1.1.2 GigabitEthernet1/0/0
127.0.0.0/20 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
Step 2 Enable MPLS and MPLS LDP globally and on all the interfaces on the nodes.
# Configure P1.
<P1> system-view
[P1] mpls lsr-id 1.1.1.9
[P1] mpls
[P1-mpls] quit
[P1] mpls ldp
[P1-mpls-ldp] quit
[P1] interface gigabitethernet 1/0/0
[P1-GigabitEthernet1/0/0] mpls
[P1-GigabitEthernet1/0/0] mpls ldp
[P1-GigabitEthernet1/0/0] quit
[P1] interface gigabitethernet 2/0/0
[P1-GigabitEthernet2/0/0] mpls
[P1-GigabitEthernet2/0/0] mpls ldp
[P1-GigabitEthernet2/0/0] quit
# Configure P2.
<P2> system-view
[P2] mpls lsr-id 2.2.2.9
[P2] mpls
[P2-mpls] quit
[P2] mpls ldp
[P2-mpls-ldp] quit
[P2] interface gigabitethernet 1/0/0
[P2-GigabitEthernet1/0/0] mpls
[P2-GigabitEthernet1/0/0] mpls ldp
[P2-GigabitEthernet1/0/0] quit
[P2] interface gigabitethernet 2/0/0
[P2-GigabitEthernet2/0/0] mpls
[P2-GigabitEthernet2/0/0] mpls ldp
[P2-GigabitEthernet2/0/0] quit
# Configure P3.
<P3> system-view
[P3] mpls lsr-id 3.3.3.9
[P3] mpls
[P3-mpls] quit
[P3] mpls ldp
[P3-mpls-ldp] quit
[P3] interface gigabitethernet 1/0/0
[P3-GigabitEthernet1/0/0] mpls
[P3-GigabitEthernet1/0/0] mpls ldp
[P3-GigabitEthernet1/0/0] quit
[P3] interface gigabitethernet 2/0/0
[P3-GigabitEthernet2/0/0] mpls
Huawei AR1200 Series Enterprise Routers
Configuration Guide - MPLS 2 MPLS LDP Configuration
Issue 01 (2011-12-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
113