Huawei AR1200 Series - Page 17

OSPF 10 3 D 10.3.1.2 GigabitEthernet2/0/0
10.1.1.0/30 Direct 0 0 D 10.1.1.1 GigabitEthernet1/0/0
10.1.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
10.1.1.2/32 Direct 0 0 D 10.1.1.2 GigabitEthernet1/0/0
10.2.1.0/30 OSPF 10 2 D 10.1.1.2 GigabitEthernet1/0/0
10.3.1.0/30 Direct 0 0 D 10.3.1.1 GigabitEthernet2/0/0
10.3.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
10.3.1.2/32 Direct 0 0 D 10.3.1.2 GigabitEthernet2/0/0
10.4.1.0/30 OSPF 10 2 D 10.3.1.2 GigabitEthernet2/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
The next hop or outgoing interface of the static LSP on 4.4.4.9/32 from LSRA to LSRD is
determined by the routing table. It is shown in boldface. In this example, the next hop IP address
is 10.1.1.2/30.
In the following example, the display on LSRD is used.
[LSRD] display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 15
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.9/32 OSPF 10 3 D 10.2.1.1 GigabitEthernet1/0/0
OSPF 10 3 D 10.4.1.1 GigabitEthernet2/0/0
2.2.2.9/32 OSPF 10 2 D 10.2.1.1 GigabitEthernet1/0/0
3.3.3.9/32 OSPF 10 2 D 10.4.1.1 GigabitEthernet2/0/0
4.4.4.9/32 Direct 0 0 D 127.0.0.1 InLoopBack0
10.1.1.0/30 OSPF 10 2 D 10.2.1.1 GigabitEthernet1/0/0
10.2.1.0/30 Direct 0 0 D 10.2.1.2 GigabitEthernet1/0/0
10.2.1.1/32 Direct 0 0 D 10.2.1.1 GigabitEthernet1/0/0
10.2.1.2/32 Direct 0 0 D 127.0.0.1 InLoopBack0
10.3.1.0/30 OSPF 10 2 D 10.4.1.1 GigabitEthernet2/0/0
10.4.1.0/30 Direct 0 0 D 10.4.1.2 GigabitEthernet2/0/0
10.4.1.1/32 Direct 0 0 D 10.4.1.1 GigabitEthernet2/0/0
10.4.1.2/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
The next hop or outgoing interface of the static LSP on 1.1.1.9/32 from LSRD to LSRA is
determined by the routing table. It is shown in boldface. In this example, the next hop IP address
is 10.4.1.1/30.
Step 3 Configure the basic MPLS capability on each LSR.
# Configure LSRA.
[LSRA] mpls lsr-id 1.1.1.9
[LSRA] mpls
[LSRA-mpls] quit
# Configure LSRB.
[LSRB] mpls lsr-id 2.2.2.9
[LSRB] mpls
[LSRB-mpls] quit
# Configure LSRC.
[LSRC] mpls lsr-id 3.3.3.9
[LSRC] mpls
[LSRC-mpls] quit
# Configure LSRD.
[LSRD] mpls lsr-id 4.4.4.9
[LSRD] mpls
Huawei AR1200 Series Enterprise Routers
Configuration Guide - MPLS 1 Static LSPs Configuration
Issue 01 (2011-12-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10