40 – English
Technical data
Technical data
NOTE! This spark ignition system complies with the Canadian ICES-002 standard.
Recommended cutting equipment for USA
Following is a list of recommended cutting equipment for Husqvarna chain saw models 357XP, 357XPG, 357XP E-tech,
357XPG E-tech, 359, 359 E-tech, 359G and 359G E-tech. These chain saw models equipped with either of the listed
bar and saw chain combination(s), fulfills the requirements according to ANSI B175.1-2000 (Gasoline Powered Chain
Saws - Safety Requirements).
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which
will also achieve kickback reduction.
Chain saw models Husqvarna 357XP, 357XPG, 357XP E-tech, 357XPG E-tech, 359, 359 E-tech, 359G and 359G E-
tech met the kickback performance requirements of ANSI B175.1-2000 when tested with the combinations of bars and
saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw chain since it met the
requirements for low kickback saw chain outlined in ANSI B175.1-2000. We recommend to use only the listed
combinations of bars and chains for chain saw models Husqvarna 357XP, 357XPG, 357XP E-tech, 357XPG E-tech, 359,
359 E-tech, 359G and 359G E-tech. Other chain saw models may not meet the kickback requirements when equipped
with the listed guide bar and saw chain combinations.
357XPXPG/E-tech 359/G/E-tech
Engine
Cylinder displacement, cu.in/cm
3
3,45/56,5 3,60/59,0
Cylinder bore, inch/mm 1,81/46 1.85/47
Stroke, inch/mm 1,34/34,0 1,34/34,0
Idle speed, rpm 2700 2700
Power, kW/ rpm 3,2/4.4 @ 9600 2,9/3,9 @ 9000
Emissions Durability Period according to California
Air Resources Board, h.
300 300
Ignition system
Spark plug
NGK BPMR 7A/
Champion RCJ 7Y
NGK BPMR 7A/
Champion RCJ 7Y
Electrode gap, inch/mm 0.02/0,5 0.02/0,5
Fuel and lubrication system
Fuel tank capacity, US pint/litre 1,43/0,68 1,43/0,68
Oil pump capacity at 9,000 rpm, ml/min 6-17 6-17
Oil tank capacity, US pint/litre 0,80/0,38 0,80/0,38
Type of oil pump Automatic Automatic
Weight
Chain saw without bar or chain, empty tanks, lb/kg
12,1/5,5: 357 XP, 357 XP E-tech
12,3/5,6: 357 XPG, 357 XPG E-
tech
12,1/5,5: 359, 359 E-tech
12,3/5,6: 359 G, 359 G E-tech
Chain/bar
Standard bar length, inch/cm 15”/38 15”/38
Recommended bar lengths, inch/cm 13-24"/33-61 13-24"/33-61
Usable cutting length, inches/cm 12-23"/31-58 12-23"/31-58
Pitch, inch/mm 0.325/8,25 0.325/8,25
3/8" /9,52 3/8" /9,52
Thickness of drive links, inch/mm 0.050/1,3 0.050/1,3
0.058/1,5 0.058/1,5
Drive sprocket type/teeth Rim/7 Rim/7
Chain speed at 133% of maximum engine power
speed, ft/s / m/s.
93.5/28,5 87.3/26,6
To Next Page
Loading...
