Husqvarna FE 501 US 2021

Questions and Answers

B
Brandon HowardAug 18, 2025
What causes high oil consumption in a Husqvarna FE 501 US 2021 Motorcycle?
- J
  Jordan PetersonAug 18, 2025
  High oil consumption in your Husqvarna Motorcycle can stem from several causes. A bent engine vent hose can be the culprit, so ensure the vent hose is routed without bends, or replace it if necessary. An engine oil level that's too high can also contribute, so check the engine oil level. If the engine oil is too thin (low viscosity), change the engine oil and the oil filter, and clean the oil screens. Lastly, worn piston and cylinder can lead to high oil consumption, so measure the piston/cylinder mounting clearance.
G
Glenn LoganAug 20, 2025
Why is my Husqvarna Motorcycle engine not starting but turning over?
- M
  michelle95Aug 20, 2025
  If your Husqvarna Motorcycle engine turns but doesn't start, several issues could be the cause. It might be an operating error, so try the start procedure again. Check if the quick release coupling is joined. A blown fuse (Fuse 1 or Fuse 4) could also be the problem, so replace the fuses. Other potential causes include an incorrectly set idle speed (adjust it), a spark plug that's oily or wet (clean, dry, or replace it), a spark plug gap that's too wide (adjust to 1.0 mm), a defective ignition system (check it), a frayed short-circuit cable in the wiring harness or a faulty switch-off button or emergency OFF switch (check the wiring harness and electrical system), or an error in the electronic fuel injection (read the fault memory using the Husqvarna Motorcycles diagnostics tool).
P
Paul MolinaAug 23, 2025
What to do if my Husqvarna FE 501 US 2021 engine cannot be cranked?
- T
  Tony HernandezAug 23, 2025
  If the engine of your Husqvarna Motorcycle cannot be cranked, it could be due to several reasons. First, ensure you are following the correct start procedure. If that's not the issue, check the 12-V battery; it might be discharged and need charging. Also, inspect the main fuse and replace it if it's blown. The starter relay or the starter motor itself could be defective, so check them as well.
O
odyerAug 26, 2025
Why does my Husqvarna FE 501 US 2021 Motorcycle engine overheat?
- B
  Bethany VasquezAug 26, 2025
  Your Husqvarna Motorcycle engine might overheat due to several reasons. Check if the coolant level is low or if there are any leaks in the cooling system. Ensure sufficient airflow and switch off the engine when stationary. Dirty radiator fins can also cause overheating, so clean them. Other potential causes include foam formation in the cooling system (drain and refill the coolant), a bent radiator hose (replace it), a defective thermostat (check it; guideline opening temperature: 70 °C (158 °F)), or a defect in the radiator fan system (check fuse 3 and the radiator fan).
R
Russell MendozaAug 28, 2025
What to do if my Husqvarna Motorcycle engine dies during the trip?
- S
  Stephanie CamposAug 28, 2025
  If your Husqvarna Motorcycle engine dies during a trip, the first thing to check is the fuel level; you might be out of fuel, so refuel. Additionally, check fuses 1 and 4, and replace them if they are blown.
N
Nicholas JacksonAug 30, 2025
Why does my Husqvarna FE 501 US 2021 Motorcycle engine have too little power?
- M
  Michael NelsonAug 31, 2025
  If your Husqvarna Motorcycle engine has too little power, several factors could be responsible. A heavily contaminated air filter could be the cause, so clean the air filter and air filter box. Additionally, a very dirty fuel filter or fuel screen could be restricting fuel flow, so replace the fuel filter and fuel screen. An error in the electronic fuel injection could also be the culprit; in this case, read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
K
Kari CarpenterSep 2, 2025
Why is my Husqvarna Motorcycle 12-V battery discharged?
- Z
  zacharymaldonadoSep 2, 2025
  If your Husqvarna Motorcycle 12-V battery is discharged, it could be because the alternator isn't charging it properly; check the charging voltage and the stator winding of the alternator. Another possibility is an undesired power consumer draining the battery; check the open-circuit current.
J
Jennifer ConradSep 4, 2025
Why doesn't my Husqvarna FE 501 US 2021 Motorcycle engine speed up?
- A
  anthony81Sep 4, 2025
  If your Husqvarna Motorcycle engine does not speed up, it could be due to an error in the electronic fuel injection; read out the fault memory using the Husqvarna Motorcycles diagnostics tool. Alternatively, the ignition system might be defective; check the secondary winding of the ignition coil, the spark plug connector, and the stator winding of the alternator.
T
Tracy BriggsSep 7, 2025
What does it mean when the malfunction indicator lamp lights up on my Husqvarna FE 501 US 2021 Motorcycle?
- D
  Dr. Kathy Howell DDSSep 7, 2025
  If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, it indicates an error in the electronic fuel injection. Check the wiring for damage and the electrical plug-in connectors for corrosion and damage. You should also read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
D
David RobinsonSep 9, 2025
What to do if the high beam, low beam, tail light, position light, and license plate lamp are not working on my Husqvarna FE 501 US 2021?
- J
  Jason AcostaSep 10, 2025
  If the high beam, low beam, tail light, position light, and license plate lamp are not working on your Husqvarna Motorcycle, it is likely due to a blown fuse 2. Replace the fuse.

Summary

Safety Advice

General Safety Instructions

Emphasizes reading all safety instructions and the importance of warning labels on the product.

Degrees of Risk and Symbols Explained

Explains danger, warning, caution, and note symbols and their associated risk levels.

Safe Operation Guidelines

Provides crucial safety advice for operating the vehicle, including rider fitness.

Protective Clothing Requirements

Highlights the importance of wearing appropriate protective clothing for safety.

Motorcycle Controls Overview

Engine Shut-off Button (EU Models)

Explains the function of the switch-off button on the left handlebar for EU models.

Emergency OFF Switch (EU Models)

Describes the emergency OFF switch on the right handlebar and its function for EU models.

Starter Button Location

Locates the start button on the right handlebar for both EU and US models.

Combination Switch Functions

Explains the combination switch on the left handlebar for selecting engine mappings and traction control.

Indicator Lamps Overview (EU Models)

Illustrates and describes the function of various indicator lamps on the instrument panel for EU models.

Indicator Lamps Overview (FE US Models)

Illustrates and describes indicator lamps for FE US models, including malfunction and fuel level warning.

Steering Lock Mechanism (EU Models)

Explains the steering lock located on the left side of the steering head for EU models.

Locking the Steering (EU Models)

Provides instructions and safety notes for locking the steering mechanism for EU models.

Unlocking the Steering (EU Models)

Details the procedure and safety advice for unlocking the steering for EU models.

Preparing Motorcycle for Use

First Use Preparation Advice

Covers crucial first-use advice, including rider fitness, protective gear, and vehicle checks.

Engine Running-in Procedure

Provides guidelines for engine break-in, specifying engine speed and performance limits.

Preparation for Difficult Operating Conditions

Advises on checks for difficult conditions like sand or mud, noting increased wear.

Riding Instructions

Pre-Ride Checks and Maintenance

Lists essential pre-ride checks for safety and proper vehicle condition.

Starting the Motorcycle Safely

Covers the procedure for starting the motorcycle, including safety warnings about exhaust gases.

Activating Traction Control System

Explains how to activate and deactivate traction control, with a warning about road use.

Gear Shifting and Riding Techniques

Guides on shifting gears, riding techniques, and clutch usage to avoid wear.

Braking Procedures and Warnings

Provides instructions and warnings on braking, including proper application and potential issues.

Safe Stopping and Parking Procedures

Describes how to safely stop and park the motorcycle, including warnings about hot components.

Refueling Procedures and Safety

Covers refueling procedures, safety warnings about fuel, and fuel quality.

Service Schedule

Required Maintenance Work Schedule

Lists routine maintenance tasks categorized by operating hours for motorsports use.

Chassis Tuning Guide

Checking Basic Chassis Setting with Rider Weight

Explains how to adjust basic chassis settings based on rider weight for optimal riding.

Adjusting Low-Speed Shock Absorber Compression

Details how to adjust the low-speed compression damping on the shock absorber for different riding styles.

Adjusting High-Speed Shock Absorber Compression

Explains how to adjust the high-speed compression damping on the shock absorber for different riding styles.

Adjusting Shock Absorber Rebound Damping

Describes how to adjust the rebound damping on the shock absorber for different riding styles.

Adjusting Shock Absorber Spring Preload

Guides on adjusting the shock absorber spring preload, including preparatory and finishing work.

Adjusting Riding Sag for Shock Absorber

Outlines the process for adjusting riding sag, including choosing and mounting a suitable spring.

Adjusting Fork Compression Damping

Explains how to adjust compression damping on the fork for different settings.

Adjusting Fork Rebound Damping

Details how to adjust rebound damping on the fork for different settings.

Adjusting Fork Spring Preload

Guides on adjusting fork spring preload using T-grips, including warnings and settings.

Service Work on the Chassis

Checking Steering Head Bearing Play

Describes how to check for play in the steering head bearing and the consequences of incorrect play.

Adjusting Steering Head Bearing Play

Provides instructions and torque specifications for adjusting the steering head bearing play.

Removing the Fuel Tank

Covers safety warnings and preparatory work for removing the fuel tank.

Installing the Fuel Tank

Details safety warnings and main work for installing the fuel tank, including cable routing.

Cleaning the Motorcycle Chain

Provides instructions for cleaning the motorcycle chain, including safety warnings and recommended products.

Checking Chain Tension

Explains how to check chain tension and the consequences of incorrect tension.

Adjusting Chain Tension

Guides on adjusting chain tension, including how to measure it and potential issues.

Checking Chain, Sprockets, and Guide

Details how to check wear on the chain, sprockets, and guide, and when to replace them.

Checking;Correcting Hydraulic Clutch Fluid

Covers checking and correcting the hydraulic clutch fluid level, including safety and substance notes.

Changing Hydraulic Clutch Fluid

Details the procedure and safety precautions for changing the hydraulic clutch fluid.

Brake System Maintenance

Checking Brake Disc Condition

Details how to check brake disc thickness, wear limits, and for damage.

Checking Front Brake Fluid Level

Covers checking the front brake fluid level and actions if it's low or old.

Adding Front Brake Fluid

Provides instructions and warnings for adding front brake fluid.

Checking Front Brake Linings

Explains how to check front brake lining thickness, damage, and cracking.

Changing Front Brake Linings

Guides on changing front brake linings, including warnings and approved parts.

Checking Foot Brake Lever Free Travel

Adjusting Foot Brake Lever Basic Position

Checking Rear Brake Fluid Level

Covers checking the rear brake fluid level and actions if it's low or old.

Adding Rear Brake Fluid

Checking Rear Brake Linings

Explains how to check rear brake lining thickness, damage, and cracking.

Changing Rear Brake Linings

Guides on changing rear brake linings, including warnings and approved parts.

Wheels and Tires Maintenance

Removing the Front Wheel

Installing the Front Wheel

Removing the Rear Wheel

Installing the Rear Wheel

Checking Tire Condition

Checking Tire Pressure

Electrical System Maintenance

Removing the 12-V Battery

Installing the 12-V Battery

Charging the 12-V Battery

Covers procedures for charging the 12-V battery, including safety, voltage checks, and charger use.

Changing the Main Fuse

Changing Fuses for Individual Consumers

Checking Headlight Alignment

Describes how to check and adjust the headlight beam alignment for proper visibility.

Adjusting Headlight Range

Explains how to adjust the headlight range for optimal road illumination, considering vehicle weight.

Diagnostics Connector Location

Cooling System Maintenance

Checking Antifreeze and Coolant Level

Details how to check coolant level and antifreeze protection, with safety warnings.

Checking Coolant Level in Radiator

Provides instructions for checking the coolant level in the radiator, including safety warnings.

Engine Tuning Procedures

Checking Throttle Cable Play

Adjusting Throttle Cable Play

Adjusting Throttle Response Characteristic Map

Explains how to change the engine's throttle response by swapping guide plates.

Changing Engine Mapping Modes

Describes how to activate different engine mappings (STANDARD/ADVANCED) using the combination switch.

Adjusting Engine Idle Speed

Details how to adjust the engine idle speed using the adjusting screw, with safety warnings.

Teaching Throttle Valve Position

Service Work on the Engine

Changing the Fuel Screen

Checking Engine Oil Level

Explains how to check the engine oil level at different temperatures and when to add oil.

Changing Engine Oil, Filter, and Cleaning Screens

Provides a comprehensive guide to changing engine oil, filter, and cleaning oil screens, including safety and environmental notes.

Adding Engine Oil

Details the process of adding engine oil, including safety warnings and recommended oil performance.

Cleaning and Care Instructions

Motorcycle Cleaning Procedure

Provides detailed instructions for cleaning the motorcycle, including safety warnings and methods.

Winter Operation Checks and Maintenance

Motorcycle Storage Guide

Long-Term Storage Procedures

Details steps for long-term storage, including fuel, cleaning, battery, and storage location.

Preparing for Use After Storage

Guides on preparing the motorcycle for use after a period of storage.

Troubleshooting Common Issues

Engine Starting Faults

Lists common faults, their possible causes, and recommended actions for diagnosis and repair.

Engine Running Faults

Continues the troubleshooting guide, listing more faults, causes, and actions.

Blink Code Diagnostics

Information on Blink Codes

Malfunction Indicator Lamp Blink Codes

Additional Malfunction Indicator Lamp Codes

Technical Data Specifications

Engine Specifications

Provides detailed technical specifications for the engine, including design, displacement, and valve clearance.

Engine Tightening Torques

Lists torque specifications for various engine components, including recommended threadlockers.

Chassis Specifications

Provides technical data related to the chassis, including frame, fork, shock absorber, and weights.

Electrical System Specifications

Fork Specifications

Shock Absorber Specifications

Chassis Tightening Torques

Lists torque specifications for various chassis components.