Why does my Husqvarna GARDENA SILENO life Lawn Mower have a wheel drive problem?
If your Husqvarna Lawn Mower is experiencing a 'Wheel drive problem', the wheel motor might be faulty; check its function when idling. Alternatively, the main circuit board could be faulty, or the cabling to the wheel motor might be damaged. Consider replacing the wheel motor if the damage isn't repairable.
What causes the 'Wheel motor overloaded' error on a Husqvarna Lawn Mower?
If your Husqvarna Lawn Mower displays 'Wheel motor overloaded', grass or another object might be wrapped around the drive wheel. Examine the drive wheel and clear any obstructions.
How to unblock the wheel motor on a Husqvarna GARDENA SILENO life?
If the Husqvarna Lawn Mower reports a 'Wheel motor blocked', it's likely that grass or another object has become wrapped around the drive wheel. Inspect the drive wheel and remove any obstructions.
Why is the cutting system blocked on my Husqvarna Lawn Mower?
If your Husqvarna Lawn Mower's cutting system is blocked, grass or other objects might be wrapped around the blade disc; check and remove any obstructions. If the blade disc is in a pool of water, move the product and fix the water collection issue. Also, the blade motor could be defective, so check its speed. The main circuit board or the cabling to the blade motor might also be faulty; consider replacing them if necessary.
What to do if Husqvarna GARDENA SILENO life goes outside working area?
If your Husqvarna Lawn Mower is showing 'Outside working area', it could be due to several reasons related to the boundary wire. Check that the boundary wire connections to the charging station are correct and that the wire isn't too close to the edge of the working area. Also, ensure the working area doesn't slope too much at the boundary wire and that the wire isn't laid in the wrong direction around an island. If there's interference from nearby installations or magnetic objects, try moving the boundary wire or creating additional islands. You can also try generating a new loop signal.
Why does my Husqvarna Lawn Mower say 'No loop signal'?
If your Husqvarna Lawn Mower shows 'No loop signal', several factors could be at play. A broken boundary wire is a common cause; inspect the LED on the charging station. Also, verify that the boundary wire is correctly connected to the charging station and that the power supply is properly connected and undamaged. The pairing between the product and charging station may be broken, so try generating a new loop signal. Ensure the boundary wire isn't laid incorrectly around an island. Metal objects or buried cables might cause disturbances; try moving the boundary wire or creating additional islands. Finally, if ECO mode is on, place the product in the charging station, start it, and close the hatch.
How to troubleshoot a battery problem on a Husqvarna Lawn Mower?
If your Husqvarna Lawn Mower has a 'Battery problem' it may be that the battery is not connected properly, or faulty, so check that the battery is properly connected. It is also possible that you are using the wrong type of battery, so use only original batteries recommended by the manufacturer.
What to do if Husqvarna Lawn Mower is stuck in the charging station?
If your Husqvarna Lawn Mower is 'Stuck in charging station', an object might be preventing it from leaving; remove the object. Alternatively, the product might be sliding on the baseplate; try cleaning it.
General| Model | GARDENA SILENO life |
|---|---|
| Type | Robotic lawnmower |
| Cutting Width | 22 cm |
| Cutting Height | 20-50 mm |
| Max Area Capacity | 600 m² |
| Maximum Slope | 35% |
| Battery Voltage | 18 V |
| Battery Type | Li-ion |
| Battery Capacity | 2.1 Ah |
| Typical Mowing Time on One Charge | 65 min |
| Typical Charging Time | 60 min |
| Weight | 8.3 kg |
| Blade Type | 3 pivoting blades |
| Mulching Capability | Yes |
| Rain Sensor | Yes |
| Smart Connectivity | Yes |
| Warranty | 2 years |
Defines warning, caution, and note terminology, and provides general safety advice for operation.
Covers specific safety measures for thunderstorms, battery handling, and maintenance procedures.
Step-by-step instructions for programming main, HMI, COM, and sensor circuit boards.
Instructions for replacing main, HMI, COM, and sensor circuit boards within the product.
Procedures for replacing battery, ventilation filter, keypad, cutting module, and wheel motors.
Checklist and actions for regular product servicing and maintenance.
Lists and explains various fault and information messages displayed by the product.
Describes common symptoms during mowing, searching, docking, and charging, with potential causes.
Procedures for finding breaks in the boundary loop wire and performing battery performance tests.
To Next Page