Why does my Husqvarna GARDENA SILENO R100LiC have a battery problem?
If your Husqvarna Lawn Mower displays 'Battery problem', it could be due to several reasons. The battery might not be connected properly, so dismantle the mower and check the battery connection. The battery might be faulty, so check the connection again. Ensure you are using only original batteries from Husqvarna. The main circuit board could also be faulty.
Why does my Husqvarna GARDENA SILENO R100LiC have no drive?
If your Husqvarna Lawn Mower has 'No drive', it might be caught in something. Free the mower and fix the cause. If it is due to wet grass, wait until the lawn dries. The working area might have a steep slope; isolate slopes steeper than 40%. If the guide wire is on a slope, ensure it's laid at an angle across the slope.
Why does my Husqvarna GARDENA SILENO R100LiC need manual charging?
If your Husqvarna Lawn Mower displays 'Needs manual charging', the mower is set to the Secondary area operating mode. Place the mower in the charging station; this is normal and requires no further action.
Why does my Husqvarna GARDENA SILENO R100LiC have no loop signal?
If your Husqvarna Lawn Mower displays 'No loop signal', it could be due to several reasons. The boundary wire might be broken, or the power supply isn't connected. Also, the connection between the mower and charging station may be broken. The boundary wire could be laid incorrectly around an island, or there might be disturbances from metal objects or buried cables. The power voltage cable could be damaged or not connected, or the boundary wire isn't connected to the charging station. If ECO mode is on, place the mower in the charging station, press START, and close the hatch. Check the LED on the charging station to troubleshoot the loop signal.
What to do if Husqvarna GARDENA SILENO R100LiC Lawn Mower goes outside working area?
If your Husqvarna Lawn Mower is 'Outside working area', it can be due to crossed boundary wire connections at the charging station. The boundary wire might be too close to the edge or laid incorrectly around an island. The working area may slope too much at the boundary wire. If there are disturbances from magnetic objects or the mower has hard time distinguishing the signal from an installation close by, try moving the boundary wire and creating additional islands or generate a new loop signal.
What to do if Husqvarna GARDENA SILENO R100LiC Lawn Mower cutting system is blocked?
If your Husqvarna Lawn Mower says 'Cutting system blocked', grass or another object may be wrapped around the blade disc. Check the blade disc and remove any object. The blade disc might be in a pool of water, so move the mower and fix the water collection issue. The blade motor could be defective, so ensure it has the right speed. The main circuit board might be defective, so change it. The cabling to the blade motor could be damaged or faulty, so check and repair or replace the blade motor.
How to get Husqvarna GARDENA SILENO R100LiC unstuck when it is trapped?
If your Husqvarna Lawn Mower is 'Trapped', it means the mower has got caught in something. Free the mower and fix the reason it became trapped. The mower might be stuck behind obstacles, so check for anything making it hard to move. Also, check that the body is properly secured in the front and rear rubber dampers, as one of the body’s attachments may have come loose.
What to do if Husqvarna Lawn Mower wheel motor is blocked?
If your Husqvarna Lawn Mower displays 'Wheel motor blocked, right/left', it means grass or another object has wrapped around the drive wheel. Check the drive wheel and remove any objects.
What does it mean when Husqvarna GARDENA SILENO R100LiC says mower lifted?
If your Husqvarna Lawn Mower shows 'Mower lifted', the lift sensor has been activated because the mower got stuck. Free the mower and fix the reason it got stuck. One of the lift sensor magnets might be inverted or missing, so check the magnets. The lift sensor itself could be faulty, so check it.
What to do if Husqvarna Lawn Mower has wheel drive problem?
If your Husqvarna Lawn Mower displays 'Wheel drive problem, right/left', the wheel motor may be faulty, so check its function when idling. The main circuit board could be faulty, so replace it. The cabling to the wheel motor might be damaged, so check if it's repairable or replace the wheel motor.
General| Brand | Husqvarna |
|---|---|
| Model | GARDENA SILENO R100LiC |
| Category | Lawn Mower |
| Language | English |
Lists technical specifications for Automower® 310 and 315 models.
Lists technical specifications for GARDENA R100Li/R100LIC and R130Li/R130LiC and R160Li.
Provides information on the Li-Ion battery and its charging.
Provides guidelines for optimal placement of the charging station.
Explains the requirement for a charging station and boundary loop.
Instructions for installing the guide wire.
Introduces the Autocheck EXP service program and its uses.
Explains how to connect the mower to the computer for service.
Describes the user interface and main functions of Autocheck EXP.
Explains the comprehensive Auto Test and Manual Test functions.
Covers software updates, log book use, and service modes.
General guidelines and safety precautions for performing repairs.
Step-by-step guide to removing and reattaching the mower's body.
Instructions for separating and joining the mower's chassis halves.
Step-by-step guide to disassembling and reassembling the charging station.
Initial steps: update software, reset settings, check basic causes.
Lists error messages, causes, and recommended actions.
Categorizes symptoms by situation (mowing, searching, docking, charging).
Provides guidance on troubleshooting loop signal issues using charging station LED.
Methods for locating breaks in the boundary loop wire.
Explains why and how to perform a battery test and evaluate results.
To Next Page