Why does my Husqvarna McCULLOCH ROB S600 Lawn Mower have a wheel drive problem?
If your Husqvarna Lawn Mower is experiencing a 'Wheel drive problem', the wheel motor might be faulty; check its function when idling. Alternatively, the main circuit board could be faulty, or the cabling to the wheel motor might be damaged. Consider replacing the wheel motor if the damage isn't repairable.
What causes the 'Wheel motor overloaded' error on a Husqvarna McCULLOCH ROB S600 Lawn Mower?
If your Husqvarna Lawn Mower displays 'Wheel motor overloaded', grass or another object might be wrapped around the drive wheel. Examine the drive wheel and clear any obstructions.
How to unblock the wheel motor on a Husqvarna McCULLOCH ROB S600 Lawn Mower?
If the Husqvarna Lawn Mower reports a 'Wheel motor blocked', it's likely that grass or another object has become wrapped around the drive wheel. Inspect the drive wheel and remove any obstructions.
Why is the cutting system blocked on my Husqvarna McCULLOCH ROB S600 Lawn Mower?
If your Husqvarna Lawn Mower's cutting system is blocked, grass or other objects might be wrapped around the blade disc; check and remove any obstructions. If the blade disc is in a pool of water, move the product and fix the water collection issue. Also, the blade motor could be defective, so check its speed. The main circuit board or the cabling to the blade motor might also be faulty; consider replacing them if necessary.
What to do if Husqvarna McCULLOCH ROB S600 goes outside working area?
If your Husqvarna Lawn Mower is showing 'Outside working area', it could be due to several reasons related to the boundary wire. Check that the boundary wire connections to the charging station are correct and that the wire isn't too close to the edge of the working area. Also, ensure the working area doesn't slope too much at the boundary wire and that the wire isn't laid in the wrong direction around an island. If there's interference from nearby installations or magnetic objects, try moving the boundary wire or creating additional islands. You can also try generating a new loop signal.
Why does my Husqvarna Lawn Mower say 'No loop signal'?
If your Husqvarna Lawn Mower shows 'No loop signal', several factors could be at play. A broken boundary wire is a common cause; inspect the LED on the charging station. Also, verify that the boundary wire is correctly connected to the charging station and that the power supply is properly connected and undamaged. The pairing between the product and charging station may be broken, so try generating a new loop signal. Ensure the boundary wire isn't laid incorrectly around an island. Metal objects or buried cables might cause disturbances; try moving the boundary wire or creating additional islands. Finally, if ECO mode is on, place the product in the charging station, start it, and close the hatch.
How to troubleshoot a battery problem on a Husqvarna Lawn Mower?
If your Husqvarna Lawn Mower has a 'Battery problem' it may be that the battery is not connected properly, or faulty, so check that the battery is properly connected. It is also possible that you are using the wrong type of battery, so use only original batteries recommended by the manufacturer.
What to do if Husqvarna McCULLOCH ROB S600 Lawn Mower is stuck in the charging station?
If your Husqvarna Lawn Mower is 'Stuck in charging station', an object might be preventing it from leaving; remove the object. Alternatively, the product might be sliding on the baseplate; try cleaning it.
General| Type | Robotic lawn mower |
|---|---|
| Cutting Width | 16 cm |
| Cutting Height, min-max | 20-50 mm |
| Maximum Slope Performance | 25 % |
| Area Capacity | 600 m² |
| Typical mowing time on one charge | 60 minutes |
| Typical charging time | 60 minutes |
| Battery Type | Lithium-ion |
| Engine Type | Electric |
Provides essential safety guidelines, including blade proximity and product modification warnings.
Covers specific safety advice for maintenance, thunderstorms, and battery handling.
Describes boundary and guide wire signals (A, F, Guide) essential for product operation.
Details the A signal, its strength variations, and how to test the boundary loop installation.
Explains the guide loop's function and signal characteristics for returning to the charging station.
Covers the installation process and obtaining login credentials for the Autocheck service tool.
Explains how to connect the robotic mower to the computer using a USB service cable.
Covers procedures for programming circuit boards, including handling blocked boards.
Provides step-by-step instructions for programming a blocked HMI circuit board.
Details the process for programming a blocked main circuit board in boot mode.
Explains how to program a new main circuit board, including options and service mode.
Provides step-by-step instructions for disassembling the product's body system.
Details the process for disassembling the upper chassis of the product.
Guides on how to replace the product's battery, including steps and post-replacement checks.
Lists common fault and information messages, their causes, and recommended actions.
Describes common symptoms encountered during mowing, searching, docking, and charging.
Provides guidance on troubleshooting loop signal issues, including LED indicators and wire breaks.
Details how to perform and evaluate a battery test to check for performance issues.
To Next Page
