Husqvarna Rider 318 User Manual

Husqvarna Rider 318

36 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

EE

EE

nn

nn

gg

gg

ll

ll

ii

ii

ss

ss

hh

hh

Rider 318

Rider 320 AWD

Oper

ator

′

s manual

Please r

ead the operator’s manual carefully and make sure you

understand the instructions before using the machine.

Table of Contents

Questions and Answers:

P
Patrick GarciaAug 19, 2025
How to troubleshoot a Husqvarna Rider 318 when the engine does not start?
- A
  Angel CookAug 20, 2025
  If your Husqvarna Lawn Mower engine doesn't start, several factors could be at play. First, ensure that the fuel tank has enough fuel; if it's empty, fill it. A faulty spark plug can also prevent the engine from starting, so consider replacing it. Inspect the ignition cable for any defects and replace if necessary. Additionally, dirt in the carburettor or fuel line can cause starting issues, so clean these components. If the starter motor isn't turning the engine over, it may need to be checked and repaired. Finally, a defective safety switch can also prevent the engine from starting; consider replacing it.
N
Nathan TaylorAug 22, 2025
What to do if the starter motor does not turn over the engine on my Husqvarna Rider 318?
- J
  janetterrellAug 22, 2025
  If the starter motor on your Husqvarna Lawn Mower isn't turning over the engine, there are several potential causes. The battery might be flat, so try charging or replacing it. Check the connection between the cable and battery to ensure it's secure. Make sure the lift lever for the cutting unit is in the correct position. A blown main fuse could also be the culprit, so replace it if necessary. If the ignition lock is faulty, it will need to be replaced. Ensure that the brake is activated. Finally, the starter motor itself might be faulty and require repair or replacement.
V
Valerie SandersAug 25, 2025
Why does my Husqvarna Rider 318 engine not run smoothly?
- A
  Allen MartinAug 25, 2025
  If your Husqvarna Lawn Mower engine isn't running smoothly, several factors could be responsible. Check the spark plug for faults and replace it if necessary. The carburettor settings might be incorrect, so adjust them accordingly. A clogged air filter can also cause rough running, so clean or replace it. Ensure the fuel tank vent isn't blocked. A defective ignition key can also cause this issue, so replace it if needed. Dirt in the carburettor or fuel line can also lead to poor performance, so clean these components. Finally, check the throttle cable for choking or incorrect adjustment, and adjust it as necessary.
R
Renee ChapmanAug 26, 2025
Why is my Husqvarna Rider 318 Lawn Mower mowing unevenly?
- M
  Michelle SingletonAug 26, 2025
  If your Husqvarna Lawn Mower is producing an uneven cut, several factors could be contributing. Start by checking if the blades are blunt and sharpen them if necessary. Avoid mowing long or wet grass, as this can affect the cut quality. Ensure the cutting unit isn't skewed and align it if needed. Clear any grass blockage under the hood. Make sure the tyre pressures are equal on both sides. Avoid over-speeding and reduce the speed if necessary. Ensure the engine speed isn't too low and increase it if needed. Finally, check if the drive belt is slipping and adjust or replace it.
D
darryl82Aug 28, 2025
What to do if the battery does not charge on my Husqvarna Rider 318 Lawn Mower?
- J
  Jeremy BerryAug 28, 2025
  If the battery on your Husqvarna Lawn Mower isn't charging, it could be due to one or more faulty battery cells, in which case you should replace the faulty battery cells. Another possibility is poor contact on the battery terminal cable connectors; improve the contact in this case.
P
pcarterAug 29, 2025
Why does my Husqvarna Rider 318 Lawn Mower engine seem to have no power?
- R
  Robert FloresAug 29, 2025
  If your Husqvarna Lawn Mower engine seems to have no power, several potential issues could be the cause. A clogged air filter can restrict airflow, so clean or replace it. A faulty spark plug can also reduce engine power, so replace it if necessary. Check for dirt in the carburettor or fuel line, and clean these components if needed. The carburettor settings might be incorrect, so adjust them. Finally, ensure the throttle cable isn't choking or incorrectly adjusted, and adjust it as necessary.
M
Marissa WatsonAug 31, 2025
Why won't the starter motor turn over on my Husqvarna Ride-on mower?
- N
  nicholasbassSep 1, 2025
  If the starter motor on your Husqvarna Ride-on mower isn't turning the engine over, several factors could be at play. First, ensure the parking brake is applied. Also, check that the lift lever for the cutting deck is not in the mowing position. A blown main fuse, a poor connection between the cable and the battery, or a weak battery can also prevent the starter motor from working. Finally, the ignition lock or the starter motor itself may be defective.
S
Sylvia AtkinsSep 2, 2025
Why does my Husqvarna Ride-on mower engine have no power?
- A
  austincoleSep 3, 2025
  If your Husqvarna Ride-on mower engine seems to lack power, the air filter might be clogged. Other potential causes include a defective spark plug, dirt in the carburetor or fuel line, or an incorrectly adjusted throttle cable.
T
Tony JonesSep 4, 2025
How to improve the cutting result of my Husqvarna Ride-on mower?
- B
  Beverly AllenSep 5, 2025
  An unsatisfactory cutting result with your Husqvarna Ride-on mower can stem from several issues. The blades might be blunt, or the grass may be too long or wet. Other possible causes include a skew cutting deck, grass blockage in the cutting deck, different tire pressures on each side, operating the product at too high a speed, too low engine speed or a slipping drive belt.
K
krista37Sep 6, 2025
What causes a Husqvarna Rider 318 engine to overheat?
- S
  Sarah SmithSep 6, 2025
  If your Husqvarna Lawn Mower engine is overheating, several factors could be the cause. The engine might be overloaded, so reduce the load. A faulty spark plug can also contribute to overheating, so replace it. Check for blockages in the air intake or cooling flanges and unblock them. A damaged fan can also cause overheating, so replace it. Ensure there's enough oil in the engine and replenish if needed. Finally, a defective ignition system can also lead to overheating, so repair or replace it.

Husqvarna Rider 318 Specifications

General

Cylinders	2
Fuel Type	Gasoline
Fuel Tank Capacity	12 L
Cutting Width	103 cm
Cutting Height	25-75 mm
Transmission Type	Hydrostatic
Drive	Rear-wheel drive
Max Speed	10 km/h
Engine Type	4-stroke
Engine Net Power RPM	3600 rpm
Uncut Circle	0 cm
Turning Radius	0 cm

Summary

Service Journal

Pre-delivery Service

After the First 8 Hours

What is What?

Location of Controls

Identification and description of all controls and components on the machine.

Safety Instructions

General Safety Guidelines

Essential safety rules and warnings for operating the machine.

General Use Precautions

Key precautions for general operation to ensure safety.

Operational Safety Practices

Driving on Slopes Safely

Detailed safety instructions for operating the machine on inclines.

Child Safety

Crucial safety measures to protect children in the work area.

Transport Safety

Guidelines for safely securing and transporting the machine.

Presentation of the Rider

Parking Brake Operation

Fueling Procedures

Safe and correct procedures for refueling the machine.

Release Lever Usage

Driving the Rider

Before Starting Engine

Essential checks and preparations before starting the engine.

Starting the Engine

Step-by-step instructions for starting the engine.

Starting with a Weak Battery

Connecting Jump Leads

Operating the Rider

How to drive and control the machine.

Stopping the Engine

Correct procedures for safely stopping the engine.

Maintenance Procedures

Maintenance Schedule Overview

A comprehensive list of maintenance tasks and their recommended intervals.

Cleaning the Machine

Parking Brake Adjustment (Rider 318)

Parking Brake Adjustment (Rider 320 AWD)

Fuel Filter Replacement

Air Filter Replacement

Ignition System Maintenance

Safety System Check

Tyre Pressure Check

Fitting the Cutting Head

Step-by-step instructions for attaching the cutting unit to the machine.

Removing the Cutting Unit

Step-by-step instructions for detaching the cutting unit from the machine.

Cutting Unit Ground Pressure

Cutting Unit Parallelism Check

Adjusting Cutting Unit Parallelism

Replacing Cutting Unit Belts

Cutting Unit Service Position

How to place the cutting unit in a vertical service position for maintenance.

Restoring from Service Position

Checking the Blades

Lubrication and Fluid Checks

Checking Engine Oil Level

Procedure for checking the engine oil level.

Replacing Engine Oil

Instructions for changing the engine oil.

Changing the Oil Filter

Procedure for replacing the engine oil filter.

Checking Transmission Oil Level

How to check the oil level in the transmission.

General Lubrication Points

Technical Data and Specifications

Machine Dimensions

Physical dimensions, weight, and wheelbase of the Rider.

Engine Specifications

Details on engine brand, output, displacement, and speed.

Electrical System Details

Noise and Cutting Width

Sound Level Data

Vibration Level Data

Transmission and Cutting Unit Specs

Cutting Unit Specifications

Specific cutting widths, heights, and blade lengths for each cutting unit.

Related product manuals

Preview: Husqvarna Rider 316T

Husqvarna Rider 316T

Husqvarna Rider 316T AWD

Husqvarna Rider 316T/s AWD

Husqvarna Rider 316TXs AWD

Husqvarna Rider 322T

Husqvarna Rider 320 AWD

Husqvarna Rider

Preview: Husqvarna Rider 13

Husqvarna Rider 13

Husqvarna Rider 18

Husqvarna Rider 13C

Preview: Husqvarna Rider 15T

Husqvarna Rider 15T

Preview: Husqvarna Rider 850

Husqvarna Rider 850